Remote Controls for CA, OR and WA (2024)

Table of Contents
Overview Programming yourRemote Set TV power,volume, and mute If you can't find the TV code Set TVinput If you can't find the TV code A/V volume, and mute IfYou can't find the Audio/Video device code Remote Control Pairing Using the Remote Batteries Button Descriptions Switching Modes (IR / RF) Usingthe Remote Finder feature (TiVo T6, Pace MG2 Only) Performing a Global Reset Overview Programming yourRemote Set TV power,volume, and mute If youcan't find the TV code Set TVinput If youcan't find the TV code A/V volume,and mute Ifyoucan't find the Audio/Video devicecode Remote Control Pairing - Pair YourRemote to Your TiVo Box Using theTiVo Series 5 Remote Batteries Button Descriptions Switching Modes (IR / RF) Usingthe Remote Finder feature (TiVo T6 AND Pace MG2Only) Performing a Global Reset Programming the Series 4 Remote TV Power, volume, and mute A/V volume and mute TV Input Using Code Search When You Can't find the Code Resetting the TiVo remote Button Functions TiVo 'Slide' Remote Program Remote Using the Popular Brands Method Four-Digit Code Programming Method Auto Search Method Code Number Readback Programming the System On/Off Button Volume Control Video Input Button Your remote's WATCH CABLE Button Battery Info Button Functions Programming Your Cable Converter Programming Other Devices Point and Press Programming Code Number Readback Programming Volume Control Installing / Replacing Batteries General Reset Programming Your Cable Converter Programming Other Devices Point and Press Programming Programming Volume Control Installing / Replacing Batteries General Reset Programming Your Cable Converter Programming Other Devices Point and Press Programming Code Number Readback Programming Volume Control Installing / Replacing Batteries General Reset Program Remote Using the Popular Brands Method Three-Digit Code Programming Method Auto Search Method Code Number Readback Volume Control Battery Info Memory Lock Resetting The Remote Programming TV using Code Entry Method Programming TV Using Point and Press Method TV Code Readback Programming Volume Control Batteries Memory Guard Resetting Your Remote Identifying the 270 vs. 271 Auto-Search Programming (recommended) Manual Programming Method Pairing the 271 Remote - RF Mode Unpairing the 271 Remote Volume Control Programming Your Cable Converter Programming Other Devices Point and Press Programming Code Number Readback Buttton Functions Installing / Replacing Batteries General Reset Three-Digit Code Programming Method Point and Press® Programming Code NumberReadback ALL POWER Smart Key Volume Control Mode Lock INPUT Button General Reset Programming Devices into the URC1056 Remote Setting Up aCombo Unit: Searching forCodes Code Number Read Back: Channel Control Lock Locking Channel Control to CBL Volume Lock Unlocking Volume Control for a Single Device (Individual Volume Unlock) Unlocking All Volume Control (Global Volume Unlock) Locking Volume Control To One Mode (Global Volume Lock) Cable ID Lock Macro Keys Programming a Macro Key Clearing a Macro Key Master Power Key Programming the Master Power Key Using the Master Power Key Clearing the Master Power Key Re-Assigning Device Keys Activating Backlighting(Optional Models) Clearing Custom Programming Automatic Programming Manual Programming Recalling aDevice Code ProgrammingVolume Control Master PowerControl Channel Lock Button Descriptions Automatic Programming Manual Programming Recalling aDevice Code ProgrammingVolume Control Master PowerControl Channel Lock Button Descriptions Automatic Programming Manual Programming Recalling aDevice Code ProgrammingVolume Control Master PowerControl Channel Lock Button Descriptions What Devices Can I Control? ProgrammingDevices to the Remote Searching for the code Find Your Code Controlling POWER key for Multiple Devices at Once Channel Control Lock Volume Control To Control volume and mute through the TV only: To Control volume and mute through the Cable Box only: To Control volume and mute through whatever mode the remote is in: Programming Devices into the AT8400 Remote Programming Volume Control: ProgrammingCable Receiver Searching forCodes Identifying ProgrammedCodes Quick Set Up Method Manual Programming Auto Search Method Code Number Readback Programming aSecond TV to DVD key The Learning Method Programming the'All Off' Button Volume Control Programming Channel Control Low Battery Warning Memory Lock Button Descriptions Three-Digit Code Programming Method Auto Search Method Code NumberReadback Programming a5th Device toAUX Button Programming the System On/Off Button Programming Channel Controls Volume Control Macro key(s) Low Battery Warning Memory Lock Button Functions Three-Digit Code Programming Method Auto Search Method Code NumberReadback Programming a5th Device toAUX Button Programming the System On/Off Button Programming Channel Controls Volume Control Macro key(s) Low Battery Warning Memory Lock Button Functions Three-Digit Code Programming Method Auto Search Method Code NumberReadback The Learning Method Programming a5th Device toAUX Button Programming the System On/Off Button Programming Channel Controls Volume Control Macro (blank) Button Low Battery Warning Memory Lock Button Functions Three-Digit Code Programming Method Auto Search Method Code NumberReadback Programming aSecond TV toAUX Button Programming the System On/Off Button Programming Channel Controls Volume Control Programming For Advanced Function (blank key) Low Battery Warning Memory Lock Button Functions Quick Set-Up Method Three-Digit Code Programming Method Auto Search Method Code NumberReadback Programming a4th Device toAUX Button Programming the System On/Off Button Programming Channel Controls Volume Control Low Battery Warning Memory Lock Button Functions Three-Digit Code Programming Method Auto Search Method Code NumberReadback The Learning Method Programming a5th Device toAUX Button Programming the System On/Off Button Programming Channel Controls Volume Control Macro Buttons Low Battery Warning Memory Lock Button Functions Three-Digit Code Programming Method Auto Search Method Code NumberReadback Programming a5th Device toAUX Button Programming the System On/Off Button Programming Channel Controls Volume Control Programming For Advanced Function (blank key) Low Battery Warning Memory Lock Button Functions Automatic Programming Manual Programming Recalling a Device Code ProgrammingVolume Control Master Power Control Channel Lock Button Descriptions Three-Digit Code Programming Method Auto Search Method Code Number Readback Programming a Second TV to AUX Button Programming the System On/Off Button Programming Channel Controls Volume Control Low Battery Warning Memory Lock Button Functions Three-Digit Code Programming Method Auto Search Method Code NumberReadback Programming a Second TV to VCR key Programming the System On/Off Button Volume Control Low Battery Warning Memory Lock Button Functions Three-Digit Code Programming Method Auto Search Method Code NumberReadback Programming a Second TV toAUX Button Programming the System On/Off Button Programming Channel Controls Volume Control Low Battery Warning Memory Lock Button Functions Three-Digit Code Programming Method Auto Search Method Code NumberReadback Programming a Second TV toAUX Button Programming the System On/Off Button Programming Channel Controls Volume Control Low Battery Warning Memory Lock Button Functions Pair Remote to DTA in RF mode Program by TV Brand Code Can't Find Your Code? Volume Control Button Functions Resetting TheRemote Programming TV into the Remote (Popular Brands) Programming TV into the Remote (Direct Code Entry) Code Search Volume Control Button Descriptions Programming TV into the Remote (Popular Brands) Programming TV into the Remote (Direct Code Entry) Code Search Volume Control Button Descriptions Manual Programming Auto Search Method Code Number Readback Programming aSecond TV to VCR key Volume Control Programming Channel Control Low Battery Warning Memory Lock Button Descriptions Manual Programming Auto Search Method Code Number Readback Programming aSecond TV to VCR key Volume Control Programming Channel Control Low Battery Warning Memory Lock Button Descriptions Three-Digit Code Programming Method SMART SCANTM AUTOMATIC PROGRAMMING Code NumberReadback Master PowerControl Volume Control Channel Lock Button Functions Setting up Your Remote Setting up your Remote for an Auxilliary Device Codescan Recalling a Device Code Programming Volume Control Button Functions Installing/Replacing Batteries AUD Button Remote is Silver Remote is Black Green LIST Button Blue ? ? ? ? Buttons AUX Button Remote is Silver Remote is Black AUX, DVD, VCR, TV, CBL buttons on top AUX, VCR, TV, CBL buttons on top (no DVD) On Demand button at the very top INFO button just above the ? button DTA Button MODE Blue OK Button Blue SEL Button Red ? ? ? ? Buttons MOT Button Power Button Setup Button System On/Off Button LIGHT button (near bottom) Remote is Black A,B,C,D buttons M1 button under (? Day) button SHIFT/MODE button under (? Day) button A,B,C buttons (no D) Remote is silver No LIGHT button Remote is Black White ON Demand button (center) Green POWER Button White OK button Blue ENTER button Remote is silver White ON Demand button (center) Green ON Demand button (center) Grey Settings button (to the left of ? button) TV Button A,B,C, and D buttons White (glow in the dark) ? ? ? ? buttons Black ? ? ? ? buttons A,B,C buttons (no D) Big Red POWER Button on the Right No Big Red POWER Button White ? ? ? ? buttons Black ? ? ? ? buttons Big orange Menu button near the top No big orange Menu button TV Pwr Button Netflix Button No Netflix Button VCR Button Video Input Button

Introduction

Resolution Steps

Remote Identifier

Remote Controls for CA, OR and WA (1)

TiVo S6A Backlit
(IPTV)

Remote Controls for CA, OR and WA (2)

TiVo Creek Remote (IPTV)

Remote Controls for CA, OR and WA (3)

TiVo Creek Remote (TiVo Stream 4K)

Remote Controls for CA, OR and WA (4)

Experience 4
with Voice

Remote Controls for CA, OR and WA (5)

TiVo Series 5
Netflix

Remote Controls for CA, OR and WA (6)

TiVo Series 5

Remote Controls for CA, OR and WA (7)

Champion
(URC2025)

Remote Controls for CA, OR and WA (8)

Synergy V
(RC-U63CD-R)

Remote Controls for CA, OR and WA (9)

Synergy V
(RC-U62CD-R)

Remote Controls for CA, OR and WA (10)

Synergy V
(RC/RT-U62CD)

Remote Controls for CA, OR and WA (11)

Synergy V
(RC-U62SD)

Remote Controls for CA, OR and WA (12)

Synergy V
(RT-U60C)

Remote Controls for CA, OR and WA (13)

PHAZR-5
(UR5U-9000L)

Remote Controls for CA, OR and WA (14)

OCAP
(URC1056)

Remote Controls for CA, OR and WA (15)

ENT 8000

Remote Controls for CA, OR and WA (16)

ENT 6412

Remote Controls for CA, OR and WA (17)

ENT 6208

Remote Controls for CA, OR and WA (18)

AllTouch
(AT8550)

Remote Controls for CA, OR and WA (19)

AllTouch
(AT8400)

Remote Controls for CA, OR and WA (20)

UR3L-SR4

Remote Controls for CA, OR and WA (21)

CLIKR-5
(UR5U-8500L)

Remote Controls for CA, OR and WA (22)

CLIKR-5
(UR5U-8500)

Remote Controls for CA, OR and WA (23)

UR5U-8700L
UR5U-8720L

Remote Controls for CA, OR and WA (24)

UR5U-8400

Remote Controls for CA, OR and WA (25)

UR4U-MDVR-CHD2

Remote Controls for CA, OR and WA (26)

UR5L-6200L

Remote Controls for CA, OR and WA (27)

UR5U-6200

Remote Controls for CA, OR and WA (28)

ENT MOTO

Remote Controls for CA, OR and WA (29)

UJ4-EXP

Remote Controls for CA, OR and WA (30)

UR4-EXP

Remote Controls for CA, OR and WA (31)

UR3-EXP

Remote Controls for CA, OR and WA (32)

UR3-SR3

Remote Controls for CA, OR and WA (33)

UR3-SR2

Remote Controls for CA, OR and WA (34)

UR4-DCT

Remote Controls for CA, OR and WA (35)

UR4-DSR

Remote Controls for CA, OR and WA (36)

UF4-200C

Remote Controls for CA, OR and WA (37)

HD uDTA

Remote Controls for CA, OR and WA (38)

URC2069

Remote Controls for CA, OR and WA (39)

URC2068BC2

Remote Controls for CA, OR and WA (40)

DTA Remote
270/271

Remote Controls for CA, OR and WA (41)

TiVo S6A Backlit Android TV Remote


  • Pairing the Remote to The TiVo Android TV device
  • Configuring TV and AV devices
  • Voice Control
  • Button Functions
  • Troubleshooting
Remote Controls for CA, OR and WA (42)

If you are seeing a 'Pair Your TiVo Remote' Screen, follow this link.

Normally your TiVo S6A Remote will be paired with your TiVo Android TV device during initial setup. The signals run on BlueTooth technology and will work through walls, around corners, etc.

If your remote can already control the Android TV device, then it is paired. If the remote is not paired with the device:

Please note: Only one remote can be paired with one Android Box at a time. If you are using a replacement remote and have the original, you need to Unpair the original, then pair it to the Android Box using the steps below:

  1. Press and hold TiVo. While holding down TiVo, press Back. Hold both for approximately 3 seconds. The activity indicator lights up red and stays on
  2. Press VOLUME DOWN 3 timesand then press and release the OK button
  3. The activity indicator will flash red 3 times, indicating that theremote is now reset and not paired. If this is your original remote, remove the batteries so that it does not automatically pair to the equipment again. If this is your new remote, continue below
    • You'll notice it still works in IR (infrared) mode, but you can't use voice commands and the remote must be in the direct sight of the IPTV box. The remote must be paired.
  4. To pair the remote back to the IPTV box:
    1. Place or hold your remote no more than 2 feet from the IPTV box
    2. A screen that searches for Bluetooth devices should pop up. If you don't see the screen, press the TiVo button
      • Your remote indicator light starts flashing amber; this means it's trying to communicate with the IPTV box
    3. The IPTV box should automatically pair the remote. If unsuccessful, Reboot the android device using the reset button under the equipment and use the steps above if you need to.
Remote Controls for CA, OR and WA (43)

The TiVo S6A Remote works with the TiVo Android TV device to automatically configure TV and AV devices.

To control your equipment, be sure to do the following:

  1. Point the remote at the equipment when using it, making sure that there is a clear line of sight. Your TV should program automatically
  2. The Activity light on the remote should blink with each keypress. If not, try replacing the batteries
  3. You can do this with your audio device as well

Alternately, if the remote does not automatically program the TV, you can use the manual method:

  1. TiVo Home | left arrow to Menu | Settings | Remote Settings
  2. Select Remote Control Programming
  3. Follow the on-screen instructions
Remote Controls for CA, OR and WA (44)

Your TiVo S6A Remote supports voice control using Google Assistant. Press the Google Assistant button on your remote to search what’s on now, change channels, record a show, open apps, and more.


Your TiVo S6A Remote needs to be paired to the TiVo Android TV device for this to work

Remote Controls for CA, OR and WA (45)Remote Controls for CA, OR and WA (46)
Remote Controls for CA, OR and WA (47)

Voice Control Does Not Work

  • Your TiVo S6A Remote needs to be paired to the TiVo Android TV device for this to work. See Pairing the Remote to The TiVo Android TV device


TV is Displying Input Banner when I press a button not labled "Input"

  • Certain TVs respond to discrete commands differently. In some cases, disabling the CEC feature helps prevent the "Input Banner" from being displayed.
  • You can also check the "One-Touch" button setup in the "Remotes and Accessories" menu and ensure the IR One-Touch is set to OFF.

TV (or other equipment) Does not Respond to Remote

  • See Configuring TV and AV devices for instructions
  • Be sure to have a clear line of sight from the remote to the device; signals to the TV are IR and will not work through walls, around corners, etc

TiVo Creek IPTV Remote (for SEI eSTREAM PYXIX 4K)


View printable manual

  • Programming the TV PWR Key
  • Programming the INPUT Key
  • Programming the VOL and MUTE Keys
  • Code Search Method
  • Resetting, Re-Pairing Remote to Box
  • Button Descriptions
Remote Controls for CA, OR and WA (48)

Programming the TV PWR Key

  1. Turn on the device (TV or audio device)
  2. Press and hold TiVo. While holding down TiVo, press Back. Hold both for approximately 3 seconds. The activity indicator lights up red and stays on
  3. Using the numeric keys, enter the first code for your brand. The activity LED will blink 3 times and turn off
  4. Point the remote at your TV or audio device and press the Power key to see if it responds
  5. If the device does not turn off, repeat steps 3-5 using the next code listed for your brand
  6. For a TV, point the remote at the TV and press the Input, VOL and Mute keys
  7. If the TV Input or volume does not change, repeat steps 2-7, selecting the next code listed for your brand
  8. When the TV responds to key presses as expected, setup is complete
Remote Controls for CA, OR and WA (49)

Programming the INPUT Key

  1. Turn on the device (TV or audio device)
  2. Press and hold TiVo. While holding down TiVo, press Input. Hold both for approximately 3 seconds. The activity indicator lights up red and stays on
  3. Using the numeric keys, enter the first ode for your brand. The activity LED will blink 3 times and turn off
  4. Point the remote at the device and press the Input key
  5. If the TV does not display the name of a signal source, repeat steps 3-5, selecting the next code listed for your brand
Remote Controls for CA, OR and WA (50)

Programming the VOL and MUTE Keys

  1. Turn on the TV or audio device
  2. Press and hold TiVo. While holding down TiVo, press Mute. Hold both for approximately 3 seconds. The activity indicator lights up red and stays on
  3. Using the numeric keys, enter the first ode for your brand. The activity LED will blink 3 times and turn off



  4. Point the remote at the device and test each of the Vol keys
  5. If the volume does not increase, decrease and mute, repeat steps 3-5, selecting the next code listed for your brand
  6. If the volume controls all functions as expected, setup is complete
Remote Controls for CA, OR and WA (51)

Code Search Method

If you can't find the exact code for your device (for example, the TV power works, but not the volume), try this method

  1. Press and hold TiVo. While holding down TiVo, press Back. Hold both for approximately 3 seconds. The activity indicator lights up red and stays on
  2. Enter code 0999; the light will flash three times and remain lit
  3. Press Channel Up once every two seconds until the device turns off
  4. Press Power to test the code; if the device turns on, the remote is programmed
  5. If the device does not respond, turn it on manually and try these steps again
Remote Controls for CA, OR and WA (52)

If you are seeing a 'Pair Your TiVo Remote' Screen, follow this link.

  • If your remote can already control the Android TV device, then it is paired. If the remote is not paired with the device:

    Please note: Only one remote can be paired with one Android Box at a time. If you are using a replacement remote and have the original, you need to return the original, then pair the new one to the Android Box using the steps below:

    1. Place or hold your remote no more than 2 feet from the TiVo Stream 4K
    2. Press and hold the BACK, and TiVo buttons together until the activity light turns red. The light will flash yellow quickly when the remote is paired
    3. The IPTV box should automatically pair with the remote. If unsuccessful, Reboot the android device using the reset button under the equipment.The reset button can be pressed using a paper clip. If the devices are still not paired, repeat the steps above.
  • Remote Controls for CA, OR and WA (53)Remote Controls for CA, OR and WA (54)

    TiVo Creek Remote (TiVo Stream 4K)


    View Quick Setup Guide

    • Programming the TV PWR Key
    • Programming the INPUT Key
    • Programming the VOL and MUTE Keys
    • Code Search Method
    • Resetting, Re-Pairing Remote to TiVo STream 4K Device
    • Button Descriptions
    Remote Controls for CA, OR and WA (55)

    Programming the TV PWR Key

    1. Turn on the device (TV or audio device)
    2. Press and hold TiVo. While holding down TiVo, press Power. Hold both for approximately 3 seconds. The activity indicator lights up red and stays on
    3. Using the numeric keys, enter the first code for your brand. The activity LED will blink 3 times and turn off
    4. Point the remote at your TV or audio device and press the Power key to see if it responds
    5. If the device does not turn off, repeat steps 3-5 using the next code listed for your brand
    6. For a TV, point the remote at the TV and press the Input, VOL and Mute keys
    7. If the TV Input or volume does not change, repeat steps 2-7, selecting the next code listed for your brand
    8. When the TV responds to key presses as expected, setup is complete
    Remote Controls for CA, OR and WA (56)

    Programming the INPUT Key

    1. Turn on the device (TV or audio device)
    2. Press and hold TiVo. While holding down TiVo, press Input. Hold both for approximately 3 seconds. The activity indicator lights up red and stays on
    3. Using the numeric keys, enter the first ode for your brand. The activity LED will blink 3 times and turn off
    4. Point the remote at the device and press the Input key
    5. If the TV does not display the name of a signal source, repeat steps 3-5, selecting the next code listed for your brand
    Remote Controls for CA, OR and WA (57)

    Programming the VOL and MUTE Keys

    1. Turn on the TV or audio device
    2. Press and hold TiVo. While holding down TiVo, press Mute. Hold both for approximately 3 seconds. The activity indicator lights up red and stays on
    3. Using the numeric keys, enter the first ode for your brand. The activity LED will blink 3 times and turn off



    4. Point the remote at the device and test each of the Vol keys
    5. If the volume does not increase, decrease and mute, repeat steps 3-5, selecting the next code listed for your brand
    6. If the volume controls all functions as expected, setup is complete
    Remote Controls for CA, OR and WA (58)

    Code Search Method

    If you can't find the exact code for your device (for example, the TV power works, but not the volume), try this method

    1. Press and hold TiVo. While holding down TiVo, press Power. Hold both for approximately 3 seconds. The activity indicator lights up red and stays on
    2. Enter code 0999; the light will flash three times and remain lit
    3. Press Channel Up once every two seconds until the device turns off
    4. Press Power to test the code; if the device turns on, the remote is programmed
    5. If the device does not respond, turn it on manually and try these steps again
    Remote Controls for CA, OR and WA (59)To reset and re-pair the remote back to the IPTV box:
    1. Place or hold your remote no more than 2 feet from the TiVo Stream 4K
    2. Press and hold the BACK, and TiVo buttons together until the activity light turns red. The light will flash yellow quickly when the remote is paired
    3. Alternately, press the button on the side of the TiVo Stream 4K for 3 seconds to display the pairing screen. Then follow the on-screen instructions
    Remote Controls for CA, OR and WA (60)See Quick Setup Guide for button descriptions

    Experience 4 Voice Remote

    • BT vs. RF
    • Programming your Remote
    • Button Descriptions
    • Switching Modes (IR, RF, BT)
    • Using the Remote Finder feature
    • Performing a Global Reset
    Remote Controls for CA, OR and WA (61)BlueTooth (BT) and Radio Frequency (RF)remotes do not require a direct line of sight; they can control a DVR anywhere within a radius of approximately 30 feet. A BlueTooth receiver, also known as a BT Dongle is needed for BT remotes unless the TiVo device has a built-in BT receiver (4K models).
    • Identifying a BT vs. RF remote:

      • Remote Controls for CA, OR and WA (62) If Last is printed in blue, the remote is a BlueTooth Remote

      • Remote Controls for CA, OR and WA (63) If Last is printed in white, the remote is an RF Remote

    Remote Controls for CA, OR and WA (64)
    • TiVos on Experience 3*:
      • Tivo Central | Settings & Messages | Settings | Remote, CableCARD, & Devices | Remote Control Setup

    *Please be aware that Voice commands cannot be utilized on Experience 3

    • TiVos on Experience 4:

      • TiVo Home | left arrow to Menu | Settings | Remote, CableCARD, & Devices | Remote Control Setup


    From the Remote Control Setup page, you will be able to select the following options:

    Set TV power, volume, and mute

    1. Select the TV brand (use Up, Down, or Ch Up, Ch Down to scroll), and press OK
    2. Hold down the TV Power and TiVo buttons together, until the light comes on solid (about 5 seconds). Then release both buttons
    3. Enter the first four-digit code from your list
    4. Try your TV Power button. If you get no response, try steps 1-3 with the next code on your list
    5. If you Can't find the TV code

      1. Cover the end of the TiVo remote control with your hand
      2. Hold down both the TiVo and TV Power buttons simultaneously until the light on remote remains lit
      3. Remove your hand and enter code 0999; the light will flash three times and remain lit
      4. Press Channel Up once every two seconds to search for the correct code
      5. Once the TV turns off, press Enter to select the code
      6. Press TV Power to test the code; if the TV turns on, the remote is programmed
      7. If the TV does not respond, try these steps again


    Set TV input

    For cycling through the video inputs of your TV

    1. Select the TV brand (use Up, Down, or Ch Up, Ch Down to scroll) and press Select
    2. Hold down the TV Input and TiVo buttons together, until the light comes on solid (about 5 seconds). Then release both buttons
    3. Enter the first four-digit code from your list
    4. Try your TV Input button. If you get no response, try steps 1-3 with the next code on your list
    5. If you Can't find the TV code

      1. Cover the end of the TiVo remote control with your hand
      2. Hold down both the TiVo and TV Input buttons simultaneously until the light on the remote control remains lit
      3. Remove your hand and enter code 0999; the light will flash three times and remain lit
      4. Press Channel Up once every two seconds to search for the correct code
      5. Once the TV changes inputs, press Enter to select the code
      6. Press TV Input to test the code; if the TV turns on, the remote is programmed
      7. If the TV does not respond, try these steps again


    A/V volume, and mute

    1. Select the Audio/Video device brand (use Up, b, or Ch Up, Ch Down to scroll) and press Select
    2. Hold down the Mute and TiVo buttons together, until the light comes on solid (about 5 seconds). Then release both buttons
    3. Enter the first four-digit code from your list
    4. Try your Mute button. If you get no response, try steps 1-3 with the next code on your list
    5. If You Can't find the Audio/Video device code
      1. Cover the end of the TiVo remote control with your hand
      2. Hold down both the TiVo and Mute buttons simultaneously until the light on the remote control remains lit
      3. Remove your hand and enter code 0999; the light will flash three times and remain lit
      4. Press Channel Up once every two seconds to search for the correct code
      5. Once the volume mutes, press Enter to select the code
      6. Press TV Input to test the code; if the TV turns on, the remote is programmed
      7. If the TV does not respond, try these steps again

    Pair your Remote Control with Your TiVo Box

    1. If you see this option, your remote can be paired to your TiVo via BT/RF signals. This is only available on 6 tuner and Mini 2 models
    2. While on this screen, your remote should automatically start pairing within seconds. If not, press the TiVo and Back buttons together until the light at the top of the remote remains lit. Release the buttons and the light will blink yellow/amber while pairing
    3. When the light stops blinking, press the TiVo button to return to the Home page
    4. Press the blue Voice (microphone) button on the remote, to confirm the blue Voice icon appears on your TV screen. Your TiVo box is now Voice enabled
    5. If this does not work:
      1. Go to TiVo Home| left arrow to Menu | Setting | Remote, CableCard & Devices | Remote Setup | Pair your remote to your TiVo Box | Reset Remote Control Pairing | Unpair All Remote Controls
      2. Press the TiVo and Back button to begin re-pairing
    Remote Controls for CA, OR and WA (65)
    Remote Controls for CA, OR and WA (66)The Remote ActivityLight indicates when a button on theremote is pressed. When in BT/RF mode, the lightis yellow. When in IR mode, the light is red.

    Remote Controls for CA, OR and WA (67)

    The TiVo Button takes you to the 'TiVo Home' page; pressingit a second time takes you to 'My Shows'.

    Remote Controls for CA, OR and WA (68)

    If programmed, TVPower turns your TV on/off.
    Remote Controls for CA, OR and WA (69)Live TV takes you to live TVfrom the TiVo screens. It also swaps fromdifferent tuners so that you can watch somethingwhile recording something else.
    Remote Controls for CA, OR and WA (70)If programmed, Inputchanges the input source on your TV. Use thisbutton to select the input the TiVo is connectedto or to switch to other equipment like a VCR orDVD player.
    Remote Controls for CA, OR and WA (71) Info allows you to see thechannel banner while watching live TV; pressingit again makes it disappear. It also allows youto see the Program Details screen while in theprogram information screen, giving youadditional information about the program.
    Remote Controls for CA, OR and WA (72)Back returns you to theprevious screen, state, or function within theTiVo menus.
    Remote Controls for CA, OR and WA (73)

    Exit out ofthe menu/guide to watch your Live program orrecording or close apps

    and...

    Select the wayyour widescreen television will displaystandard (4:3) programming by going to astandard definition channel and pressing thisbutton. Your 4:3 programming can display inPanel (sidebars), Full (Stretch) or Zoom.

    Remote Controls for CA, OR and WA (74) Remote Controls for CA, OR and WA (75) Remote Controls for CA, OR and WA (76) Remote Controls for CA, OR and WA (77)The Arrow Buttonsare used to navigate the TiVo menus and the TiVoLive Guide. The up and down arrows allow you toscroll through the menus. The right arrow willselect a menu option. The left arrow takes youback to the last screen you were on.
    Remote Controls for CA, OR and WA (78)OK is used in the TiVomenus or the Live Guide to choose menu optionsor shows to record.
    Remote Controls for CA, OR and WA (79)Voice command - press and hold thebutton, and speak naturally into the remote.Release the button when you have finishedspeaking. Here are some things you can do withvoice:
    • Can't decidewhat to watch?
      • Say "Showme comedies on tonight" "or "Show actionmovies playing at 9 pm" and instantlysee results, avoiding time-consuming andclunky searches.
    • Ask for aspecific show
      • Play thelatest episode of Modern Family
    • Change channels effortlessly
      • Say "channel 2-5-1" or use the channel namelike "ESPN"
    • Instantlyset up a OnePass
      • "Set up a Onepass for Big Bang Theory"
    • Don't feellike digging through endless pages of theProgram Guide?
      • Say "Showme what's on tonight" and TiVo willdisplay shows and movies you might liketo watch based on shows you?e watchedbefore
    • Trying tofind something specific but can? rememberthe name?
      • Tell TiVoto ?how me action movies?and then digfurther by saying "Just the ones withBruce Willis? TiVo will get you to whatyou?e looking for faster!
    • Want to showyour friends something cool?
      • Use yourfavorite movie quote! Say "Hasta lavista, baby" into your remote and watchas "Terminator 2" appears moments later.
    • Search bymovie or show title, franchise, or genre
      • "DoctorWho", "Breaking Bad", "Back to theFuture"
    • Search byactor, director, or producer
      • "Moviesdirected by Steven Spielberg" or "Show me movieswith George Clooney and Julia Roberts"
    • Search forMenu commands or apps
      • "Settings","My Shows", "Hulu", "show me theGuide", "Show me action movies on Netflix"
    Remote Controls for CA, OR and WA (80)Guide takes you to the TiVoLive Guide or Grid Guide where you can chooseprograms to watch or record. Pressing it againclears the guide from the screen.
    Remote Controls for CA, OR and WA (81)If programmed, Volumeincreases and decreases the volume on your TV orstereo.
    Remote Controls for CA, OR and WA (82)If programmed, Muteturns off the audio of your TV or stereo.
    Remote Controls for CA, OR and WA (83)Channel up/down changes the channelon the TiVo and allows you to page up or downwhile in the TiVo menus.
    Remote Controls for CA, OR and WA (84)Thumbs Up lets you give shows youlike a positive rating. You can give a show upto three thumbs up. These ratings are used bythe TiVo to choose programs to record for TiVoSuggestions.
    Remote Controls for CA, OR and WA (85)Record starts recording theshow you are currently watching.
    Remote Controls for CA, OR and WA (86)Thumbs Down lets you give showsyou don't like a negative rating. You can give ashow up to three thumbs down. These ratings areused by the TiVo to choose programs to recordfor TiVo Suggestions.
    Remote Controls for CA, OR and WA (87)Play will start playing arecorded show from Now Playing. When you areusing pause, rewind, fast-forward or slow,pressing Play will resume playing at normalspeed.
    Remote Controls for CA, OR and WA (88)Rewind rewinds a program. Pressit up to three times for three speeds. Press ita fourth time to resume playing. When the TiVois paused, it allows you to go backframe-by-frame.
    Remote Controls for CA, OR and WA (89)Slow plays a recording orlive TV in slow motion. Use in conjunction withFF or REW buttons for frame-by-frame motion.
    Remote Controls for CA, OR and WA (90)Fast-Forward fast-forwardsthrough a program. Press it up to three timesfor three speeds. Press it a fourth time toresume playing. When the TiVo is paused, itallows you to advance frame-by-frame.
    Remote Controls for CA, OR and WA (91)Pause freezes a recorded showor live TV. Pressing it again resumes playing.
    Remote Controls for CA, OR and WA (92)Instant Replay repeats the last 8seconds of the program on a recording or liveTV.

    This button alsowill take TV Listings back 24 hours at a time.

    Remote Controls for CA, OR and WA (93)The On Demand buttontakes you directly to Video On Demand.
    Remote Controls for CA, OR and WA (94)The NETFLIXbutton takes you directly to the NETFLIX App.
    Remote Controls for CA, OR and WA (95)Advance jumps ahead 30 secondswhen watching recorded programming. Hold downmore than 2 seconds and it will take you to theend the show. If you are watching live(buffered) TV, you can use it to catch up to thelive broadcast.

    Use in conjunctionwith FF or REW buttons to skip to each 15minute tick marker.

    This button alsowill take TV Listings forward 24 hours at atime.

    Remote Controls for CA, OR and WA (96) Remote Controls for CA, OR and WA (97) Remote Controls for CA, OR and WA (98)Remote Controls for CA, OR and WA (99)A, B, C, D -Special options used throughout TiVo'sInteractive Guide for sorting and filteringresults.
    Remote Controls for CA, OR and WA (100)Number buttons allow you to enterchannel numbers.

    Numbers 0, 1, 2,3, 4, 5, and 6 also take you to shortcuts inthe guide while in TiVo central.

    Number 0 takes youto the TiVo animation while in TiVo central.

    Remote Controls for CA, OR and WA (101)Clear removes the channel banner onlive TV or a recorded program. You can alsouse it to delete programs from My Shows.
    Remote Controls for CA, OR and WA (102) or Remote Controls for CA, OR and WA (103) Enter/Last returns you to thelast channel the TiVo was tuned to in live TV.

    If Last isprinted in blue,the remote is a BlueToothRemote.

    If Last isprinted in white, the remote is a RFRemote

    Remote Controls for CA, OR and WA (104)In IR mode, the remote will work with ANY of our TiVos.

    To enter IR mode:

    Press and hold the Remote Controls for CA, OR and WA (105) + Remote Controls for CA, OR and WA (106) buttons until the activity indicatoron the remote control lights. The remote remainsin IR mode until you enter the key combinationthat puts the remote into BT/ RF mode.

    Switching to BT/RF mode (for 6 Tuner TiVos):

    Entering BT/RF mode causes a paired remote that iscurrently operating in IR mode to switch to BT/ RFmode. This procedure has no effect in New Pairingmode or when the remote is unpaired.

    To change the remote control from IR mode to BT/RFmode, press and hold the Remote Controls for CA, OR and WA (107) + Remote Controls for CA, OR and WA (108)buttons until the activity indicator on the remotecontrol lights.

    Remote Controls for CA, OR and WA (109)Are you always losing yourremote? The TiVo T6 remote uses a remote finderfeature to help you locate your missing remote.
    • On the T6, touch the amber image of the remote control on the front of the DVR:
      Remote Controls for CA, OR and WA (110)
    • On the MG2, the remote finder button is on the back of the DVR:
      Remote Controls for CA, OR and WA (111)
    • When pressed, aTiVo jingle will play on the remote
    • When you find theremote, press any button to deactivate thesound, or just wait 15 seconds for it to turnoff automatically

    IMPORTANT: The remotemust be in BT/ RF mode for this to work

    Remote Controls for CA, OR and WA (112)The Global Reset functionun-pairs the remote from the paired DVR, then clearsany other remote settings, such as IR codes for yourtelevision or other A/V device. Use this function tounpair a remote and return it to the out-of-boxsettings.

    IMPORTANT:You will need both the paired remote and theDVR to perform a global reset. If your paired remotehas been lost or damaged, you will need to use a newremote in IR mode to put the DVR in a pairing state,then pair the new remote to the DVR. Forinstructions, see To Pair a different remote to yourDVR.

    1. Press and hold theRemote Controls for CA, OR and WA (113) + Remote Controls for CA, OR and WA (114) buttonsuntil light on the remote blinks
    2. Press Remote Controls for CA, OR and WA (115) three times, then press Remote Controls for CA, OR and WA (116)
    3. The light on theremote will flash three times if the globalreset is successful

    TiVo Series 5 Netflix Remote


    >

    • TiVo Experience 3 RF Netflix
    Remote Controls for CA, OR and WA (117)

    Expand All | CollapseAll


    Overview

      This article uses some terms that might be unfamiliar. Read through this list of terms and definitions if you need clarification:

      • IR mode: In infrared (IR) mode, the remote relies on a direct line of sight to control the DVR via infrared signals. The remote is set in IR mode when you take it out of the box. IR mode does not require the remote to be paired to a specific DVR. In this mode, the remote will work with ANY of our TiVos.
      • RF mode: In radio frequency (RF) mode, the remote does not require a direct line of sight. Rather, the remote can control a DVR anywhere within a radius of approximately 30 feet. To enter RF mode, you must pair the remote to a specific DVR

      Pairing mode: Supports two methods for pairing:

      • New Pairing mode: The remote control that comes with your 6 Tuner TiVo is already in New Pairing mode. This pairing mode allows you to pair the DVR and remote control automatically by pressing any button on the remote control.
      • Allow Pairing mode: This pairing mode is for manually adding a new remote control or transferring a remote control from one DVR to another. When you put the remote control in Allow Pairing mode, it will pair with any available 6 Tuner TiVo that is accepting pairing requests within range.


      Global Reset: The Global Reset function un-pairs the remote control from the paired DVR and clears any other remote settings, such as IR codes for your TV or other A/V devices.


      Remote activity indicator colors

      When the remote control is in Allow Pairing mode, the activity indicator (the TiVo logo's antennae on the TiVo button) slowly flashes. When the remote control successfully pairs with a DVR, the activity indicator flashes quickly five times and then stops.

      When you press buttons on the remote, the activity indicator flashes different colors to indicate what kind of signal the remote is sending:

      • If the activity indicator flashes red, the remote is sending IR commands to the DVR.
      • If the activity indicator flashes amber, the remote is paired and is sending RF commands to the DVR.

      NOTE: 6 Tuner TiVos can be paired with up to 10 remote controls.

    Programming yourRemote

      For TiVos on Experience 3:

      TiVo Central | Settings & Messages | Settings | Remote, CableCARD, & Devices | Remote Control Setup

      TiVos on Experience 4:

      TiVo Home | left arrow to Menu | Settings |Remote, CableCARD, & Devices | Remote Control Setup

      From the Remote Control Setup page, you will be able to select the following options:

      Set TV power,volume, and mute

        1. Select the TV brand (use Up, b, or Ch Up, Ch Down to scroll), and press Select
        2. Hold down the TV Power and TiVo buttons together, until the light comes on solid (about 5 seconds). Then release both buttons.
        3. Enter the first four-digit code from your list
        4. Try your TV Power button. If you get no response, try steps 1-3 with the next code on your list.

      If you can't find the TV code

        1. Cover the end of the TiVo remote control with your hand
        2. Hold down both the TiVo and TV Power buttons simultaneously until thelight on remote remains lit
        3. Remove your hand and enter code 0999; the light will flash three times and remain lit

        4. Press Channel Up once every two seconds to search for the correct code

          • Once the TV turns off, press Enter to select the code
          • Press TV Powerto test the code; if the TV turns on, the remote is programmed
        5. If the TV does not respond, try these steps again

      Set TVinput

        For cycling through the video inputs of your TV

        1. Select the TV brand (use Up, b, or Ch Up, Ch Down to scroll) and press Select
        2. Hold down the TV Input and TiVo buttons together, until the light comes on solid (about 5 seconds). Then release both buttons
        3. Enter the first four-digit code from your list
        4. Try your TV Input button. If you get no response, try steps 1-3 with the next code on your list.

        If you can't find the TV code

          1. Cover the end of the TiVo remote control with your hand
          2. Hold down both the TiVo and TV Input buttons simultaneously until the light on the remote control remains lit

          3. Remove your hand and enter code 0999; the light will flash three times and remain lit
          4. Press Channel Up once every two seconds to search for the correct code
            • Once the TV changes inputs, press Enter to select the code
            • Press TV Input to test the code; if the TV turns on, the remote is programmed
          5. If the TV does not respond, try these steps again

      A/V volume, and mute

        1. Select the Audio/Video device brand (use Up, b, or Ch Up, Ch Down to scroll) and press Select
        2. Hold down the Mute and TiVo buttons together, until the light comes on solid (about 5 seconds). Then release both buttons
        3. Enter the first four-digit code from your list
        4. Try your Mute button. If you get no response, try steps 1-3 with the next code on your list.

        IfYou can't find the Audio/Video device code

          1. Cover the end of the TiVo remote control with your hand
          2. Hold down both the TiVo and Mute buttons simultaneously until the light on the remote control remains lit
          3. Remove your hand and enter code 0999; the light will flash three times and remain lit

          4. Press Channel Up once every two seconds to search for the correct code

            • Once the volume mutes, press Enter to select the code
            • Press TV Input to test the code; if the TV turns on, the remote is programmed
          5. If the TV does not respond, try these steps again

      Remote Control Pairing

        If you see this option, your remote can be paired to your TiVo via RF signals. This is only available on 6 tuner and Mini 2 models.

        1. Your remote should automatically pair to the TiVo from this page
        2. Hold your Series 5 Remote no more than 3 feet from the TiVo
        3. The Amber light on top should steadily blink until done
        4. If the remote wont pair, perform a global resetand try the above steps again

    Using the Remote

      Batteries

        Install two (2) "AA" batteries as indicated by the diagram in the battery compartment. Be careful to properly match the "+ / -" ends of the batteries with the diagram in the battery compartment.

        Remote Controls for CA, OR and WA (118)

        When the batteries become too weak to operate the remote control properly, the TiVo will start to be unresponsive to remote commands. When this happens, install 2 new "AA" size batteries.

      Button Descriptions

        Remote Controls for CA, OR and WA (119) The Remote Activity Light indicates when a button on the remote is pressed. When in RF mode, the light is yellow. When in IR mode, the light is red.

        Remote Controls for CA, OR and WA (120)

        The TiVo Button takes you to 'TiVo Central'; pressing it a second time takes you to 'My Shows'.

        Remote Controls for CA, OR and WA (121)

        If programmed, TV Power turns your TV on/off.
        Remote Controls for CA, OR and WA (122) Live TV takes you to live TV from the TiVo screens. It also swaps from different tuners so that you can watch something while recording something else.
        Remote Controls for CA, OR and WA (123) Back returns you to the previous screen, state, or function within the TiVo menus.
        Remote Controls for CA, OR and WA (124) If programmed, Input changes the input source on your TV. Use this button to select the input the TiVo is connected to or to switch to other equipment like a VCR or DVD player.
        Remote Controls for CA, OR and WA (125) Info allows you to see the channel banner while watching live TV; pressing it again makes it disappear. It also allows you to see the Program Details screen while in the program information screen, giving you additional information about the program.

        Remote Controls for CA, OR and WA (126) Remote Controls for CA, OR and WA (127) Remote Controls for CA, OR and WA (128) Remote Controls for CA, OR and WA (129)

        The Arrow Buttons are used to navigate the TiVo menus and the TiVo Live Guide. The up and down arrows allow you to scroll through the menus. The right arrow will select a menu option. The left arrow takes you back to the last screen you were on.
        Remote Controls for CA, OR and WA (130) Select is used in the TiVo menus or the Live Guide to choose menu options or shows to record.
        Remote Controls for CA, OR and WA (131) The Magnifying Glass button takes you directly to TiVo's search page.
        Remote Controls for CA, OR and WA (132)

        Exit out of the menu/guide to watch your Live program or recording

        and...

        Select the way your widescreen television will display standard (4:3) programming by going to a standard definition channel and pressing this button. Your 4:3 programming can display in Panel (sidebars), Full (Stretch) or Zoom.

        Remote Controls for CA, OR and WA (133) Guide takes you to the TiVo Live Guide or Grid Guide where you can choose programs to watch or record. Pressing it again clears the guide from the screen.
        Remote Controls for CA, OR and WA (134) If programmed, Volume increases and decreases the volume on your TV or stereo.
        Remote Controls for CA, OR and WA (135) If programmed, Mute turns off the audio of your TV or stereo.
        Remote Controls for CA, OR and WA (136) Channel up/down changes the channel on the TiVo and allows you to page up or down while in the TiVo menus.
        Remote Controls for CA, OR and WA (137) Thumbs Up lets you give shows you like a positive rating. You can give a show up to three thumbs up. These ratings are used by the TiVo to choose programs to record for TiVo Suggestions.
        Remote Controls for CA, OR and WA (138) Record starts recording the show you are currently watching.
        Remote Controls for CA, OR and WA (139) Thumbs Down lets you give shows you don't like a negative rating. You can give a show up to three thumbs down. These ratings are used by the TiVo to choose programs to record for TiVo Suggestions.
        Remote Controls for CA, OR and WA (140) Play will start playing a recorded show from Now Playing. When you are using pause, rewind, fast-forward or slow, pressing Play will resume playing at normal speed.
        Remote Controls for CA, OR and WA (141) Rewind rewinds a program. Press it up to three times for three speeds. Press it a fourth time to resume playing. When the TiVo is paused, it allows you to go back frame-by-frame.
        Remote Controls for CA, OR and WA (142) Slow plays a recording or live TV in slow motion. Use in conjunction with FF or REW buttons for frame-by-frame motion.
        Remote Controls for CA, OR and WA (143) Fast-Forward fast-forwards through a program. Press it up to three times for three speeds. Press it a fourth time to resume playing. When the TiVo is paused, it allows you to advance frame-by-frame.
        Remote Controls for CA, OR and WA (144) Pause freezes a recorded show or live TV. Pressing it again resumes playing.
        Remote Controls for CA, OR and WA (145) Instant Replay repeats the last 8 seconds of the program on a recording or live TV.

        This button also will take TV Listings back 24 hours at a time.

        Remote Controls for CA, OR and WA (146) The On Demand button takes you directly to Video On Demand.
        Remote Controls for CA, OR and WA (147) The NETFLIX button takes you directly to the NETFLIX App.
        Remote Controls for CA, OR and WA (148) Advance jumps ahead 30 seconds when watching recorded programming. Hold down more than 2 seconds and it will take you to the end the show. If you are watching live (buffered) TV, you can use it to catch up to the live broadcast.

        Use in conjunction with FF or REW buttons to skip to each 15 minute tick marker.

        This button also will take TV Listings forward 24 hours at a time.

        Remote Controls for CA, OR and WA (149) Remote Controls for CA, OR and WA (150) Remote Controls for CA, OR and WA (151) Remote Controls for CA, OR and WA (152) A, B, C, D - Special options used throughout TiVo's Interactive Guide for sorting and filtering results.
        Remote Controls for CA, OR and WA (153) Number buttons allow you to enter channel numbers.

        Numbers 1, 2, 3, 4, 5, and 6 also take you to shortcuts in the guide while in TiVo central.

        Number 0 takes you to the TiVo animation while in TiVo central.

        Remote Controls for CA, OR and WA (154) Clear removes the channel banner on live TV or a recorded program. You can also use it to delete programs from My Shows.
        Remote Controls for CA, OR and WA (155) Enter/Last returns you to the last channel the TiVo was tuned to in live TV.

      Switching Modes (IR / RF)

        In IR mode, the remote will work with ANY of our TiVos.

        To enter IR mode:

        Press and hold the Remote Controls for CA, OR and WA (156) + Remote Controls for CA, OR and WA (157) buttons until the activity indicator on the remote control lights. The remote remains in IR mode until you enter the key combination that puts the remote into RF mode.

        Switching to RF mode (for 6 Tuner TiVos):
        Entering RF mode causes a paired remote that is currently operating in IR mode to switch to RF mode. This procedure has no effect in New Pairing mode or when the remote is unpaired.

        To change the remote control from IR mode to RF mode, press and hold the Remote Controls for CA, OR and WA (158) + Remote Controls for CA, OR and WA (159) buttons until the activity indicator on the remote control lights.

      Usingthe Remote Finder feature (TiVo T6, Pace MG2 Only)

        Are you always losing your remote? The TiVo T6 remote uses a remote finder feature to help you locate your missing remote.

        • On the T6, touch the amber image of the remote control on the front of the DVR:
          Remote Controls for CA, OR and WA (160)
        • On the MG2, the remote finder button is on the back of the DVR:
          Remote Controls for CA, OR and WA (161)
        • When pressed, a TiVo jingle will play on the remote
        • When you find the remote, press any button to deactivate the sound, or just wait 15 seconds for it to turn off automatically

        IMPORTANT: The remote must be in RF mode for this to work

    Performing a Global Reset

      The Global Reset function un-pairs the remote from the paired DVR, then clears any other remote settings, such as IR codes for your television or other A/V device. Use this function to unpair a remote and return it to the out-of-box settings.

      IMPORTANT: You will need both the paired remote and the DVR to perform a global reset. If your paired remote has been lost or damaged, you will need to use a new remote in IR mode to put the DVR in a pairing state, then pair the new remote to the DVR. For instructions, see To Pair a different remote to your DVR.

        1. Press and hold the Remote Controls for CA, OR and WA (162) + Remote Controls for CA, OR and WA (163) buttons until light on the remote blinks
        2. Press Remote Controls for CA, OR and WA (164) three times, then press Remote Controls for CA, OR and WA (165)
        3. The light on the remote will flash three times if the global reset is successful

    TiVo Series 5 Remote

    • Experience 3 IR/RF
    Remote Controls for CA, OR and WA (166)

    ExpandAll | CollapseAll

    Overview

      This article uses some termsthat might be unfamiliar. Read through this list ofterms and definitions if you need clarification:

      • IR mode: In infrared (IR)mode, the remote relies on a direct line ofsight to control the DVR via infrared signals.The remote is set in IR mode when you take itout of the box. IR mode does not require theremote to be paired to a specific DVR. Inthis mode, the remote works with ANY of ourTiVos.
      • RF mode: In radiofrequency (RF) mode, the remote does not requirea direct line of sight. Rather, the remote cancontrol a DVR anywhere within a radius ofapproximately 30 feet. To enter RF mode, youmust pair the remote to a specific DVR

      Pairing mode: Supports twomethods for pairing:

      • New Pairingmode: The remote control that comes withyour 6 Tuner TiVo is already in New Pairingmode. This pairing mode allows you to pair theDVR and remote control automatically by pressingany button on the remote control.
      • Allow Pairingmode: This pairing mode is for manuallyadding a new remote control or transferring aremote control from one DVR to another. When youput the remote control in Allow Pairing mode, itwill pair with any available 6 Tuner TiVo thatis accepting pairing requests within range.


      Global Reset: The Global Reset functionun-pairs the remote control from the paired DVRand clears any other remote settings, such as IRcodes for your TV or other A/V devices.


      Remote activity indicator colors

      When the remotecontrol is in Allow Pairing mode, the activityindicator (the TiVo logo's antennae on the TiVobutton) slowly flashes. When the remote controlsuccessfully pairs with a DVR, the activityindicator flashes quickly five times and thenstops.

      When you press buttons on the remote, the activityindicator flashes different colors to indicatewhat kind of signal the remote is sending:

      • If the activityindicator flashes red, the remote is sending IRcommands to the DVR.
      • If the activityindicator flashes amber, the remote is pairedand is sending RF commands to the DVR.

      NOTE: 6 Tuner TiVoscan be paired with up to 10 remote controls.

    Programming yourRemote

      TiVos on Experience 3:

      TiVo Central |Settings & Messages | Settings | Remote,CableCARD, & Devices | Remote Control Setup

      TiVos with Experience 4

      Go to TiVo Home| left arrow to Menu | Settings | Remote,CableCard & Devices | Remote Control Setup

      From the RemoteControl Setup page, you will be ableto select the following options:

      Set TV power,volume, and mute

        1. Select the TVbrand (use Up, b, or Ch Up,Ch Down to scroll), and press Select
        2. Hold down the TVPower and TiVo buttonstogether, until the light comes on solid(about 5 seconds). Then release bothbuttons.
        3. Enter the firstfour-digit code from your list
        4. Try your TVPower button. If you get no response,try steps 1-3 with the next code on yourlist.

        If youcan't find the TV code

          1. Coverthe end of the TiVo remotecontrol with your hand
          2. Hold downboth the TiVoand TV Power buttonssimultaneously untilthelight onremote remains lit
          3. Removeyour hand and enter code 0999;the light will flash threetimes and remain lit

          4. Press Channel Up color="#800000">onceevery two seconds to searchfor the correct code

            • Oncethe TV turns off,press Enter to selectthe code
            • Press TVPowerto test thecode; if the TV turns on, the remoteis programmed
          5. If the TVdoes not respond, trythese steps again

      Set TVinput

        For cycling through thevideo inputs of your TV

        1. Select the TVbrand (use Up, b, or Ch Up,Ch Down to scroll) and press Select
        2. Hold down the TVInput and TiVo buttonstogether, until the light comes on solid(about 5 seconds). Then release both buttons
        3. Enter the firstfour-digit code from your list
        4. Try your TVInput button. If you get no response,try steps 1-3 with the next code on yourlist.

        If youcan't find the TV code

          1. Coverthe end of the TiVo remotecontrol with your hand
          2. Hold down boththe TiVo and TVInput buttons simultaneouslyuntil the light on theremote control remains lit

          3. Removeyour hand and enter code 0999;the light will flash threetimes and remain lit
          4. Press ChannelUp color="#800000">onceevery two seconds to search forthe correct code
            • Oncethe TV changes inputs,press Enter to selectthe code
            • Press TVInput to test the code;if the TV turns on, the remote isprogrammed
          5. If the TVdoes not respond, trythese steps again

      A/V volume,and mute

        1. Select theAudio/Video device brand (use Up, b,or Ch Up, Ch Down to scroll)and press Select
        2. Hold down the Muteand TiVo buttons together, until thelight comes on solid (about 5 seconds). Thenrelease both buttons
        3. Enter the firstfour-digit code from your list
        4. Try your Mutebutton. If you get no response, try steps1-3 with the next code on your list.

        Ifyoucan't find the Audio/Video devicecode

          1. Coverthe end of the TiVo remote controlwith your hand
          2. Hold downboth the TiVo and Mutebuttons simultaneouslyuntil the light on theremote control remains lit
          3. Removeyour hand and enter code 0999;the light will flash threetimes and remain lit

          4. Press ChannelUp color="#800000">once everytwo seconds to searchfor the correct code

            color="#800000">
            • Oncethe volume mutes,press Enter to selectthe code
            • Press TVInput to test the code;if the TV turns on, the remote isprogrammed
          5. If the TVdoes not respond, trythese steps again

      Remote Control Pairing - Pair YourRemote to Your TiVo Box

        If you see this option,your remote can be paired to your TiVo via RFsignals. This is only available on 6 tuner andMini 2 models.

        1. Your remoteshould automatically pair to the TiVo fromthis page
        2. Hold yourSeries 5 Remote no more than 3 feet from theTiVo
        3. The Amber lighton top should steadily blink until done
        4. Go to Live TVand test the remote
        5. For Tivo Experience 3 if theremote wont pair, perform a globalresetand try the above steps again
        6. For Tivo Experience4, if the remote won't pair, follow thesesteps:
        • Go to TiVoCentral | left arrow to Menu | Setting |Remote, CableCard & Devices | RemoteSetup | Pair your remote to your TiVoBox | Reset Remote Control Pairing |Unpair All Remote Controls
        • Press the TiVoand Back button

      Using theTiVo Series 5 Remote

        Batteries

          Install two (2) "AA"batteries as indicated by the diagram in thebattery compartment. Be careful to properlymatch the "+ / -" ends of the batteries with thediagram in the battery compartment.

          When the batteriesbecome too weak to operate the remote controlproperly, the TiVo will start to beunresponsive to remote commands. When thishappens, install 2 new "AA" size batteries.

        Button Descriptions

          Remote Controls for CA, OR and WA (167)The RemoteActivity Light indicates whena button on the remote is pressed.When in RF mode, the light is yellow.When in IR mode, the light is red.

          Remote Controls for CA, OR and WA (168)

          The TiVo Button takes you to 'TiVoCentral'; pressing it a second timetakes you to 'Now Playing'.

          Remote Controls for CA, OR and WA (169)

          If programmed,TV Power turns your TV on/off.
          Remote Controls for CA, OR and WA (170)Live TV takes you to live TV from the TiVoscreens. It also swaps from differenttuners so that you can watch somethingwhile recording something else.
          Remote Controls for CA, OR and WA (171)Backreturns you to the previous screen,state, or function within the TiVomenus.
          Remote Controls for CA, OR and WA (172)If programmed,Input changes the input sourceon your TV. Use this button to selectthe input the TiVo is connected to orto switch to other equipment like aVCR or DVD player.
          Remote Controls for CA, OR and WA (173)Info allows youto see the channel banner whilewatching live TV; pressing it againmakes it disappear. It also allows youto see the Program Details screenwhile in the program informationscreen, giving you additionalinformation about the program.

          Remote Controls for CA, OR and WA (174) Remote Controls for CA, OR and WA (175) Remote Controls for CA, OR and WA (176) Remote Controls for CA, OR and WA (177)

          The ArrowButtons are used to navigatethe TiVo menus and the TiVo LiveGuide. The up and down arrows allowyou to scroll through the menus. Theright arrow will select a menu option.The left arrow takes you back to thelast screen you were on.
          Remote Controls for CA, OR and WA (178)Select is used inthe TiVo menus or the Live Guide tochoose menu options or shows torecord.
          Remote Controls for CA, OR and WA (179)Select the wayyour widescreen television willdisplay standard (4:3) programming bygoing to a standard definition channeland pressing this button. Your 4:3programming can display in Panel(sidebars), Full (Stretch) or Zoom.

          and...

          Exit outof the menu/guide to watch your Liveprogram or recording

          Remote Controls for CA, OR and WA (180)Guide takes youto the TiVo Live Guide or Grid Guidewhere you can choose programs to watchor record. Pressing it again clearsthe guide from the screen.
          Remote Controls for CA, OR and WA (181)If programmed,Volume increases and decreasesthe volume on your TV or stereo.
          Remote Controls for CA, OR and WA (182)If programmed,Mute turns off the audio ofyour TV or stereo.
          Remote Controls for CA, OR and WA (183)Channelup/down changes thechannel on the TiVo and allows you topage up or down while in the TiVomenus.
          Remote Controls for CA, OR and WA (184)Thumbs Up lets yougive shows you like a positive rating.You can give a show up to three thumbsup. These ratings are used by the TiVoto choose programs to record for TiVoSuggestions.
          Remote Controls for CA, OR and WA (185)Record startsrecording the show you are currentlywatching.
          Remote Controls for CA, OR and WA (186)Thumbs Down lets yougive shows you don't like a negativerating. You can give a show up tothree thumbs down. These ratings areused by the TiVo to choose programs torecord for TiVo Suggestions.
          Remote Controls for CA, OR and WA (187)Play will startplaying a recorded show from NowPlaying. When you are using pause,rewind, fast-forward or slow, pressingPlay will resume playing at normalspeed.
          Remote Controls for CA, OR and WA (188)Rewind rewinds aprogram. Press it up to three timesfor three speeds. Press it a fourthtime to resume playing. When the TiVois paused, it allows you to go backframe-by-frame.
          Remote Controls for CA, OR and WA (189)Slow plays arecording or live TV in slow motion.Use in conjunction with FF or REWbuttons for frame-by-frame motion.
          Remote Controls for CA, OR and WA (190)Fast-Forwardfast-forwards through a program. Pressit up to three times for three speeds.Press it a fourth time to resumeplaying. When the TiVo is paused, itallows you to advance frame-by-frame.
          Remote Controls for CA, OR and WA (191)Pause freezes arecorded show or live TV. Pressing itagain resumes playing.
          Remote Controls for CA, OR and WA (192)InstantReplay repeats thelast 8 seconds of the program on arecording or live TV.

          Thisbutton also will take TV Listingsback 24 hours at a time.

          Remote Controls for CA, OR and WA (193)
          or
          Remote Controls for CA, OR and WA (194)
          The VODbutton takes you directly toVideo On Demand.
          Remote Controls for CA, OR and WA (195)Advance jumpsahead 30 seconds when watchingrecorded programming. Hold down morethan 2 seconds and it will take you tothe end the show. If you are watchinglive (buffered) TV, you can use it tocatch up to the live broadcast.

          Use inconjunction with FF or REW buttonsto skip to each 15 minute tickmarker.

          Thisbutton also will take TV Listingsforward 24 hours at a time.

          Remote Controls for CA, OR and WA (196) Remote Controls for CA, OR and WA (197) Remote Controls for CA, OR and WA (198) Remote Controls for CA, OR and WA (199)A, B, C, D - Special options used throughoutTiVo's Interactive Guide for sortingand filtering results.
          Remote Controls for CA, OR and WA (200)Numberbuttons allow you toenter channel numbers.

          Numbers1, 2, 3, 4, 5, and 6 also take youto shortcuts in the guide while inTiVo central.

          Number 0takes you to the TiVo animationwhile in TiVo central.

          Remote Controls for CA, OR and WA (201) Clear removes the channelbanner on live TV or a recordedprogram. You can also use it todelete programs from My Shows.
          Remote Controls for CA, OR and WA (202)Enter/Last returnsyou to the last channel the TiVo wastuned to in live TV.

        Switching Modes (IR / RF)

          In IR mode, theremote will work with ANY of our TiVos.

          To enter IRmode:

          Press and holdthe Remote Controls for CA, OR and WA (203) + Remote Controls for CA, OR and WA (204) buttons until the light on theremote turns on. The remote remains in IRmode until you enter the key combinationthat puts the remote into RF mode.

          Switching to RF mode (for 6 TunerTiVos):
          Entering RF mode causes a paired remotethat is currently operating in IR mode toswitch to RF mode. This procedure has noeffect in New Pairing mode or when theremote is unpaired.

          To change the remote control from IR mode toRF mode, press and hold the Remote Controls for CA, OR and WA (205) + Remote Controls for CA, OR and WA (206) buttons until theactivity indicator on the remote controllights.

        Usingthe Remote Finder feature (TiVo T6 AND Pace MG2Only)

          Are you always losingyour remote? The TiVo T6 remote uses a remotefinder feature to help you locate your missingremote.

          • On the T6,touch the amber image of the remotecontrol on the front of the DVR:
            Remote Controls for CA, OR and WA (207)
          • On the MG2,the remote finder button is on the back ofthe DVR:
            Remote Controls for CA, OR and WA (208)
          • When pressed,a TiVo jingle will play on the remote
          • When you findthe remote, press any button to deactivatethe sound, or just wait 15 seconds for itto turn off automatically

          IMPORTANT: Theremote must be in RF mode for this to work

      Performing a Global Reset

        The Global Resetfunction un-pairs the remote from the pairedDVR, then clears any other remote settings, suchas IR codes for your television or other A/Vdevice. Use this function to unpair a remote andreturn it to the out-of-box settings.

        IMPORTANT: You willneed both the paired remote and the DVR toperform a global reset. If your paired remotehas been lost or damaged, you will need to usea new remote in IR mode to put the DVR in apairing state, then pair the new remote to theDVR. For instructions, see To Pair a differentremote to your DVR.

          1. Press andhold the Remote Controls for CA, OR and WA (209) + Remote Controls for CA, OR and WA (210) buttons untilthe activity indicator lights up
          2. Press Remote Controls for CA, OR and WA (211) three times, then press Remote Controls for CA, OR and WA (212)
          3. The activityindicator will flash three times if theglobal reset is successful

      Series 4 TiVo

      • Series 4 TiVo

      Remote Controls for CA, OR and WA (213)

      Expand All | CollapseAll

      Programming the Series 4 Remote

        Go to:

        TiVo Central | Settings & Messages | Settings | Remote, CableCARD, & Devices | Remote Control Setup

        TV Power, volume, and mute

          1. Find the brand name of your TV from the list provided.
          2. Hold down the TV Power and TiVo buttons together, until the red light comes on solid (about 5 seconds). Then release both buttons.
          3. Enter the first four-digit code from your list.
          4. Try your TV Power button. If you get no response, try again with the next code on your list.

        A/V volume and mute

          1. Find the brand name of your device from the list provided.
          2. Hold down the Mute and TiVo buttons together, until the red light comes on solid (about 5 seconds). Then release both buttons.
          3. Enter the first four-digit code from your list.
          4. Try your Mute button. If you get no response, try again with the next code on your list.

        TV Input

          1. Find the brand name of your TV from the list provided.
          2. Hold down the TV Input and TiVo buttons together, until the red light comes on solid (about 5 seconds). Then release both buttons.
          3. Enter the first four-digit code from your list.
          4. Try your TV Input button. If you get no response, try again with the next code on your list.

        Using Code Search When You Can't find the Code

          1. Cover the end of the TiVo remote control with your hand to block the I/R signal
          2. Hold down the TiVo and TV Power buttons together until the light on the remote control remains on+
          3. Remove your hand from the end of the TiVo remote control
          4. Enter code 0999 - After entering this code, the remote control light will flash 3 times and remain on
          5. Press Channel Up once every two seconds; this will test hundreds of codes, one by one
            • Important: Going any faster than this may skip over a code that works
          6. When pressing Channel Up turns off the TV, press Enter to select the code
          7. Press TV Power button to test the code; if the TV turns on, the remote has been successfully programmed
          8. Once the TiVo remote cycles through all available codes, the remote light will go out, indicating all codes have been tried
          9. If this happened, or if the TV does not respond to the code selected, repeat these steps to make sure the code was not skipped over by cycling through the codes too fast

          The TiVo remote may not have codes for all TV models

      Resetting the TiVo remote

        1. Cover the end of the TiVo remote control with your hand
        2. Press the TiVo and the TV Power buttons simultaneously until the light at the end of the remote comes on
        3. Press Thumbs Down 3 times, followed by Enter. The remote light should go out. If the light does not go out, repeat this step

        NOTE: If the incorrect button is pressed, press Clear to start over.

      Button Functions

        Remote Controls for CA, OR and WA (214) The Remote Activity Light indicates when a button on the remote is pressed.

        Remote Controls for CA, OR and WA (215)

        The TiVo Button takes you to 'TiVo Central'; pressing it a second time takes you to 'Now Playing'.

        Remote Controls for CA, OR and WA (216)

        If programmed, TV Power turns your TV on/off.
        Remote Controls for CA, OR and WA (217) Live TV takes you to live TV from the TiVo screens. It also swaps from different tuners so that you can watch something while recording something else.
        Remote Controls for CA, OR and WA (218) If programmed, Input changes the input source on your TV. Use this button to select the input the TiVo is connected to or to switch to other equipment like a VCR or DVD player.
        Remote Controls for CA, OR and WA (219) Display or Info allows you to see the channel banner while watching live TV; pressing it again makes it disappear. It also allows you to see the Program Details screen while in the program information screen, giving you additional information about the program.

        Remote Controls for CA, OR and WA (220) Remote Controls for CA, OR and WA (221) Remote Controls for CA, OR and WA (222) Remote Controls for CA, OR and WA (223)

        The Arrow Buttons are used to navigate the TiVo menus and the TiVo Live Guide. The up and down arrows allow you to scroll through the menus. The right arrow will select a menu option. The left arrow takes you back to the last screen you were on.
        Remote Controls for CA, OR and WA (224) Select is used in the TiVo menus or the Live Guide to choose menu options or shows to record.
        Remote Controls for CA, OR and WA (225) Select the way your widescreen television will display standard (4:3) programming by going to a standard definition channel and pressing this button. Your 4:3 programming can display in Panel (sidebars), Full (Stretch) or Zoom.
        Remote Controls for CA, OR and WA (226) Guide takes you to the TiVo Live Guide or Grid Guide where you can choose programs to watch or record. Pressing it again clears the guide from the screen.
        Remote Controls for CA, OR and WA (227) If programmed, Volume increases and decreases the volume on your TV or stereo.
        Remote Controls for CA, OR and WA (228) If programmed, Mute turns off the audio of your TV or stereo.
        Remote Controls for CA, OR and WA (229) Channel up/down changes the channel on the TiVo and allows you to page up or down while in the TiVo menus.
        Remote Controls for CA, OR and WA (230) Thumb Up lets you give shows you like a positive rating. You can give a show up to three thumbs up. These ratings are used by the TiVo to choose programs to record for TiVo Suggestions.
        Remote Controls for CA, OR and WA (231) Record starts recording the show you are currently watching.
        Remote Controls for CA, OR and WA (232) Thumbs Down lets you give shows you don't like a negative rating. You can give a show up to three thumbs down. These ratings are used by the TiVo to choose programs to record for TiVo Suggestions.
        Remote Controls for CA, OR and WA (233) Play will start playing a recorded show from Now Playing. When you are using pause, rewind, fast-forward or slow, pressing Play will resume playing at normal speed.
        Remote Controls for CA, OR and WA (234) Rewind rewinds a program. Press it up to three times for three speeds. Press it a fourth time to resume playing. When the TiVo is paused, it allows you to go back frame-by-frame.
        Remote Controls for CA, OR and WA (235) Slow plays a recording or live TV in slow motion. Use in conjunction with FF or REW buttons for frame-by-frame motion.
        Remote Controls for CA, OR and WA (236) Fast-Forward fast-forwards through a program. Press it up to three times for three speeds. Press it a fourth time to resume playing. When the TiVo is paused, it allows you to advance frame-by-frame.
        Remote Controls for CA, OR and WA (237) Pause freezes a recorded show or live TV. Pressing it again resumes playing.
        Remote Controls for CA, OR and WA (238) Instant Replay repeats the last 8 seconds of the program on a recording or live TV.

        This button also will take TV Listings back 24 hours at a time.

        Remote Controls for CA, OR and WA (239)
        or
        Remote Controls for CA, OR and WA (240)
        The VOD button takes you directly to RCN Video On Demand.
        Remote Controls for CA, OR and WA (241) Advance jumps ahead 30 seconds when watching recorded programming. Hold down more than 2 seconds and it will take you to the end the show. If you are watching live (buffered) TV, you can use it to catch up to the live broadcast.

        Use in conjunction with FF or REW buttons to skip to each 15 minute tick marker.

        This button also will take TV Listings forward 24 hours at a time.

        Remote Controls for CA, OR and WA (242) Remote Controls for CA, OR and WA (243) Remote Controls for CA, OR and WA (244) Remote Controls for CA, OR and WA (245) A, B, C, D - Special options used throughout TiVo's Interactive Guide
        Remote Controls for CA, OR and WA (246) Number buttons allow you to enter channel numbers.

        Numbers 1, 2, 3, 4, 5, and 6 also take you to shortcuts in the guide while in TiVo central.

        Number 0 takes you to the TiVo animation while in TiVo central.

        Remote Controls for CA, OR and WA (247) Clear removes the channel banner on live TV or a recorded program. You can also use it to delete programs from My Shows.
        Remote Controls for CA, OR and WA (248) Enter/Last returns you to the last channel the TiVo was tuned to in live TV.

      TiVo 'Slide' Remote

        Remote Controls for CA, OR and WA (249)

        The 'Slide' remote uses the same programming instructions as above.

      Champion (URC2025)

      • Champion (URC2025)

      Remote Controls for CA, OR and WA (250)

      Expand All | CollapseAll

      This remote is programmed by default to command Motorola/Pace/Arris and Scientific Atlanta/Cisco converters. No programming to these converters is necessary.

      Program Remote Using the Popular Brands Method

        1. Turn on the equipment you wish to program (TV, DVD, AUX, or AUD)
        2. Press the device key (TV, AUDIO, DVD) the LED will light off and on again
        3. Press and hold SETUP until the mode key blinks twice
        4. Find your device and brand from the chart below and note the DIGIT key assigned to your brand.

          Using your number buttons, press and hold down the DIGIT key for your device/brand

          TV DVD/Blu Ray Audio Device Digit
          Insignia / Dynex Insignia / Dynex Bose 1
          LG / Zenith LG Denon 2
          Mitsubishi Panasonic LG 3
          Panasonic Philips / Magnavox Onkyo 4
          Philips / Magnavox RCA Panasonic 5
          Samsung Samsung Philips 6
          Sharp Sharp Pioneer 7
          Sony Sony Samsung 8
          Toshiba Sylvania Sony 9
          Vizio Toshiba Yamaha 0
        5. Press POWER to confirm the remote now controls the device. If the device does not turn off, repeat steps 2-4 using the next code for your device

        If your brand does not appear in the brand chart, perform setup using either the Four-Digit Code Programming or Code Search

      Four-Digit Code Programming Method

        1. Turn on the equipment you wish to program (TV, DVD, AUDIO)
        2. Press and release the device key (TV, DVD, AUDIO)
        3. Press and hold SETUP until the device key (TV, DVD, AUDIO) blinks once, and then twice
        4. Enter 1st code for your Audio Device brand from the code list.

          Using TV key

          Using AUDIO key

          Using DVD key

          or

        5. Press POWER to confirm the remote now controls the device. If the device does not turn off, repeat steps 2-4 using the next code for your device

      Auto Search Method

        If the four-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct code number for your equipment by the following steps:

        1. Turn on the equipment you wish to operate
        2. Press and hold SETUP until TV, DVD, or AUDIO blinks once, then twice
        3. Press the the device key you wish to program (TV, DVD, AUDIO). The mode key will stay lit
        4. Press and hold down the OK/SELECT key. Let go of the OK/SELECT key when your device turns off
        5. Press the POWER button to turn the device back on

      Code Number Readback

        To identify the 4-digit setup code for your device, follow these steps:

        1. Press the device key you wish to program (TV, DVD, AUDIO). The mode key will stay lit
        2. Press and hold SETUP until the device key (TV, DVD, AUDIO) blinks twice
        3. Press 9-9-0 on the remote. The mode key (TV, DVD, AUDIO) will blink twice
        4. To view first digit in your 4 digit code, press 1 and count the number of times the mode key blinks back
          • Press 2 and count the number of times the mode key blinks back. this is your second digit
          • Press 3 and count the number of times the mode key blinks back. this is your third digit
          • Press 4 and count the number of times the mode key blinks back. this is your fourth digit
            • NOTE: If a code digit is “0” the red light will not blink

        5. Write your device's brand & setup code for future reference

      Programming the System On/Off Button

        The System on/off button can send out up to three power on/off commands for the devices you programmed into the remote control

        1. Press [CBL]
        2. Press [System On/Off] and [OK/SEL] simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds
        3. Press [TV]
        4. Press [DVD] (if adding)
        5. Press [AUD] (if adding)
        6. Press [AUX] (if adding)
        7. Press [CH?] to save the power commands you stored. The [CBL] button will blink twice to confirm

      Volume Control

        Volume and Mute control are factory programmed to the respective Device mode you select, as follows:

        CBL : CBL TV : TV DVD : TV AUD : AUD AUX : AUX

        If you wish to store another device's volume control in CBL mode, use the following steps

        1. Press and hold SETUP until the mode key blinks twice
        2. Press VOLUME + key
        3. Press the mode key that corresponds to the device you use for volume controls

        To restore the volume control back to your TV in CBL mode, repeat the above steps by replacing [device] with [CBL] in step 3

      Video Input Button

        Remote Controls for CA, OR and WA (251)

        This button can change the input source of your TV or other electronic device while in any mode.

        • The button can change the input source of the TV (Input 1, Input 2, Aux, Game, Video 1, Video 2, etc) - this is the preferred default
        • .. or, the button can change the input source of an audio device's input (CD, DVD, TV SOUND, etc.)

        To program this button, follow the steps below:

        1. Press and hold SETUP until the mode key blinks twice
        2. Press VIDEO INPUT
        3. Press the device key that corresponds to the device you use for volume controls (TV or AUDIO)

      Your remote's WATCH CABLE Button

        Once you have programmed the remote to operate your electronic devices, you can press the WATCH CABLE button to turn your converter and TV on and off with one button press. You can also program the WATCH CABLE button to turn off/on additional devices and/or tune your TV to it's correct output channel.

        IMPORTANT:
        You must first program ALL devices on your Champion (URC2025) for the WATCH CABLE button to work correctly.

        Follow these steps if you wish to use an alternate device for volume control.

        1. Press and hold SETUP until the mode key blinks twice
        2. Press WATCH CABLE
        3. In the order you want the devices to turn on, press the mode key that corresponds to the device ONCE AT A TIME.

          For example:

          Press Remote Controls for CA, OR and WA (252), Remote Controls for CA, OR and WA (253) and the converter and TV will turn on/off in that order and puts the remote in CABLE mode.
          Press Remote Controls for CA, OR and WA (254), Remote Controls for CA, OR and WA (255), Remote Controls for CA, OR and WA (256) and the converter, TV, and Audio Device will turn on/off in that order and puts the remote in CABLE mode.
          Press Remote Controls for CA, OR and WA (257), Remote Controls for CA, OR and WA (258), Remote Controls for CA, OR and WA (259) and the TV, converter, and Audio Device will turn on/off in that order and puts the remote in CABLE mode.

      Battery Info

        Install two (2) "AA" batteries as indicated by the diagram in the battery compartment. Be careful to properly match the "+ / -" ends of the batteries with the diagram in the battery compartment.

        Remote Controls for CA, OR and WA (260)

        When the battery is low, the remote control LED blinks 2 times whenever a [device] button is pressed to turn on equipment.

      Button Functions

        Remote Controls for CA, OR and WA (261)

      Synergy V (RC-U63CD-R)


      View printable manual

      • Synergy V (RC-U63CD-R)

      Remote Controls for CA, OR and WA (262)

      Expand All | CollapseAll


      Programming Your Cable Converter

        1. Turn on your converter
        2. Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence like below:

          Remote Controls for CA, OR and WA (263)

        3. Try code 001, 002, or 003 until the converter turns off
        4. Press [MUTE]
          • If your CABLE converter turns back on, press [OK] to lock in the code
            • The mode (power) buttons will blink 3 times and go out
          • If your CABLE converter does not turn back on, repeat steps 3 and 4 until you can turn your CABLE converter off and on
        5. Write your CABLE brand & setup code down for future reference

      Programming Other Devices

        1. Turn on your device
        2. Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence:

          Remote Controls for CA, OR and WA (264)

        3. From the Setup Code list below, locate and enter the 3-digit code for your brand. If multiple codes are listed, you may have to enter several 3-digit codes until your device turns off
          • If you cannot find your code, you can use Point and Press Programming
        4. Press [MUTE]
        5. If your device turns back on, press [OK] to lock in the code
          • The mode (power) buttons will blink 3 times and go out
        6. Use your device key (AUDIO, DVD, VCR, TV) to power the device back on If your device does not turn back on, repeat steps using a different setup code
        7. Try specific commands for your device, like:
          • TV - [VOL UP], [VOL DOWN] and [MUTE]
          • VCR - Put a tape in and try [PLAY], [REWIND] and [FFWD]
          • DVD Player - Put a DVD in and try [PLAY], [Pause] and [FFWD]
          • Audio Device - [VOL UP], [VOL DOWN] and [MUTE]
        8. If your device does not work for specific commands, repeat steps using a different setup code
        9. Write your device brand & setup code for future reference

      Point and Press Programming

        1. Turn on your device
        2. Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence:

          Remote Controls for CA, OR and WA (265)

        3. Press and hold the [CH +] button until the TV turns off
        • Every time the buttons light in a sequence, the remote is trying a different code. It may take seconds or several minutes for the remote to find the proper code for your device
        • Please be patient, and be ready to release the [CH +] button when the device turns off
      • Press [MUTE]
        • If your TV turns back on, press [OK] to lock in the code. The mode (power) buttons will blink 3 times and go out
        • If your TV does not run back on, try pressing [CH -] one step at a time until that device turns back on. Each time you press the [CH -] button, the power/mode buttons will start blinking in reverse sequence:
          Remote Controls for CA, OR and WA (266)
      • Once you have found the proper code, press [OK] to lock in the code
      • Try specific commands for your device, like:
        • TV - [VOL UP], [VOL DOWN] and [MUTE]
        • VCR - Put a tape in and try [PLAY], [REWIND] and [FFWD]
        • DVD Player - Put a DVD in and try [PLAY], [Pause] and [FFWD]
        • Audio Device - [VOL UP], [VOL DOWN] and [MUTE]
      • If your device does not work for specific commands, repeat steps above

      Code Number Readback

        To identify the 3-digit setup code for your device, follow these steps:

        1. Press [device key], then [OK] - hold both down until the [device key] button lights up under finger
        2. Press [INFO]. The illuminated button will “blink back” the code number, with a 1-second interval between each digit of the code
        3. The remote will display the number "0" as the mode buttons ALL quickly flash a few times (CBL, TV, VCR, DVD, AUDIO)
        4. Example: TV Code is 3-0-1
          • [TV], [TV], [TV]
          • (one-second pause)
          • All device keys flash
          • (one-second pause)
          • [TV]

      Programming Volume Control

        By default, your remote defaults to your TV volume control (unless you are in AUDIO mode)

        To control volume commands through your CONVERTER in the remote's CABLE mode:

        1. Press [OK], then [CBL] together - hold both down until the [CBL] button lights up (under your finger)
        2. Press [VOL ], then [CBL]. The [CBL] button will blink and go out

        To control volume / mute back through your TV in the remote's CABLE mode:

        1. Press [OK], then [CBL] together - hold both down until the [CBL] button lights up (under your finger)
        2. Press [VOL ], then [TV]. The [CBL] button will blink and go out

      Installing / Replacing Batteries

        Install two (2) "AA" batteries as indicated by the diagram in the battery compartment. Be careful to properly match the "+ / -" ends of the batteries with the diagram in the battery compartment

        When the batteries become too weak to operate the remote control properly, the mode keys will become dim or not illuminate at all during use. When this happens, install 2 new "AA" size batteries

        Your remote control has Memory Guard, which eliminates reprogramming after battery changes

      General Reset

        The remote can be reset to its factory default settings if needed

        1. Press [OK], then [CBL] together until the [CBL] button lights up (under your finger)
        2. Press [1]
        3. The [CBL] button will blink 3 times and go out. All codes will now be cleared. Start programming your remote over again, as needed

      Synergy V (RC-U62CD-R)

      • Synergy V (RT-U62CDR)

      Remote Controls for CA, OR and WA (267)

      Expand All | Collapse All


      Programming Your Cable Converter

        1. Turn on your converter
        2. Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence like below:

          Remote Controls for CA, OR and WA (268)

        3. Try code 001, 002, or 003 until the converter turns off
        4. Press [MUTE]
          • If your converter turns back on, press [OK] to lock in the code
            • The mode (power) buttons will blink 3 times and go out
          • If your CABLE converter does not turn back on, repeat steps 3 and 4 until you can turn your CABLE converter off and on
        5. Write your CABLE brand & setup code down for future reference

      Programming Other Devices

        1. Turn on your device
        2. Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence:

          Remote Controls for CA, OR and WA (269)

        3. From the Setup Code list below, locate and enter the 3-digit code for your brand. If multiple codes are listed, you may have to enter several 3-digit codes until your device turns off
          • If you cannot find your code, you can use Point and Press Programming
        4. Press [MUTE]
        5. If your device turns back on, press [OK] to lock in the code
          • The mode (power) buttons will blink 3 times and go out
        6. Use your device key (AUDIO, DVD, VCR, TV) to power the device back on If your device does not turn back on, repeat steps using a different setup code
        7. Try specific commands for your device, like:
          • TV - [VOL UP], [VOL DOWN] and [MUTE]
          • VCR - Put a tape in and try [PLAY], [REWIND] and [FFWD]
          • DVD Player - Put a DVD in and try [PLAY], [Pause] and [FFWD]
          • Audio Device - [VOL UP], [VOL DOWN] and [MUTE]
        8. If your device does not work for specific commands, repeat steps using a different setup code

        9. Write your device brand & setup code for future reference

      Point and Press Programming

          1. Turn on your device
          2. Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence:

            Remote Controls for CA, OR and WA (270)

          3. Press and hold the [CH +] button until the TV turns off
        • Every time the buttons light in a sequence, the remote is trying a different code. It may take seconds or several minutes for the remote to find the proper code for your device
        • Please be patient, and be ready to release the [CH +] button when the device turns off
      • Press [MUTE]
        • If your TV turns back on, press [OK] to lock in the code. The mode (power) buttons will blink 3 times and go out
        • If your TV does not run back on, try pressing [CH -] one step at a time until that device turns back on. Each time you press the [CH -] button, the power/mode buttons will start blinking in reverse sequence:

          Remote Controls for CA, OR and WA (271)

      • Once you have found the proper code, press [OK] to lock in the code
      • Try specific commands for your device, like:
        • TV - [VOL UP], [VOL DOWN] and [MUTE]
        • VCR - Put a tape in and try [PLAY], [REWIND] and [FFWD]
        • DVD Player - Put a DVD in and try [PLAY], [Pause] and [FFWD]
        • Audio Device - [VOL UP], [VOL DOWN] and [MUTE]
      • If your device does not work for specific commands, repeat steps above

      Programming Volume Control

        By default, your remote defaults to your TV volume control (unless you are in AUDIO mode)

        To control volume commands through your CONVERTER in the remote's CABLE mode:

        1. Press [OK], then [CBL] together - hold both down until the [CBL] button lights up (under your finger)
        2. Press [VOL ], then [CBL]. The [CBL] button will blink and go out

        To control volume / mute back through your TV in the remote's CABLE mode:

        1. Press [OK], then [CBL] together - hold both down until the [CBL] button lights up (under your finger)
        2. Press [VOL ], then [TV]. The [CBL] button will blink and go out

      Installing / Replacing Batteries

        Install two (2) "AA" batteries as indicated by the diagram in the battery compartment. Be careful to properly match the "+ / -" ends of the batteries with the diagram in the battery compartment

        When the batteries become too weak to operate the remote control properly, the mode keys will become dim or not illuminate at all during use. When this happens, install 2 new "AA" size batteries

        Your remote control has Memory Guard, which eliminates reprogramming after battery changes

      General Reset

        The remote can be reset to its factory default settings if needed

        1. Press [OK], then [CBL] together until the [CBL] button lights up (under your finger)
        2. Press [1]
        3. The [CBL] button will blink 3 times and go out. All codes will now be cleared. Start programming your remote over again, as needed
        • If the [CBL] button DID NOT blink 3 times and go out, follow the alternate procedure below.

        1. Press [OK], then [CBL] together until the [CBL] button lights up (under your finger)

        2. Press [0]
        3. The [CBL] button will blink 3 times and go out. All codes will now be cleared. Start programming your remote over again, as needed

      Synergy V (Model RT-U62CD / RC-U62CD)

      • Synergy V (Model RT-U62CD / RC-U62CD)

      Remote Controls for CA, OR and WA (272)

      Expand All | Collapse All


      Programming Your Cable Converter

        1. Turn on your converter
        2. Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence like below:

          Remote Controls for CA, OR and WA (273)

        3. Try code 001, 002, or 003 until the converter turns off
        4. Press [MUTE]
          • If your converter turns back on, press [OK] to lock in the code
            • The mode (power) buttons will blink 3 times and go out
          • If your CABLE converter does not turn back on, repeat steps 3 and 4 until you can turn your CABLE converter off and on
        5. Write your CABLE brand & setup code down for future reference

      Programming Other Devices

        1. Turn on your device
        2. Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence:

          Remote Controls for CA, OR and WA (274)

        3. From the Setup Code list below, locate and enter the 3-digit code for your brand. If multiple codes are listed, you may have to enter several 3-digit codes until your device turns off
          • If you cannot find your code, you can use Point and Press Programming
        4. Press [MUTE]
        5. If your device turns back on, press [OK] to lock in the code
          • The mode (power) buttons will blink 3 times and go out
        6. Use your device key (AUDIO, DVD, VCR, TV) to power the device back on If your device does not turn back on, repeat steps using a different setup code
        7. Try specific commands for your device, like:
          • TV - [VOL UP], [VOL DOWN] and [MUTE]
          • VCR - Put a tape in and try [PLAY], [REWIND] and [FFWD]
          • DVD Player - Put a DVD in and try [PLAY], [Pause] and [FFWD]
          • Audio Device - [VOL UP], [VOL DOWN] and [MUTE]
        8. If your device does not work for specific commands, repeat steps using a different setup code

        9. Write your device brand & setup code for future reference

      Point and Press Programming

          1. Turn on your device
          2. Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence:

            Remote Controls for CA, OR and WA (275)

          3. Press and hold the [CH +] button until the TV turns off
        • Every time the buttons light in a sequence, the remote is trying a different code. It may take seconds or several minutes for the remote to find the proper code for your device
        • Please be patient, and be ready to release the [CH +] button when the device turns off
      • Press [MUTE]
        • If your TV turns back on, press [OK] to lock in the code. The mode (power) buttons will blink 3 times and go out
        • If your TV does not run back on, try pressing [CH -] one step at a time until that device turns back on. Each time you press the [CH -] button, the power/mode buttons will start blinking in reverse sequence:

          Remote Controls for CA, OR and WA (276)

      • Once you have found the proper code, press [OK] to lock in the code
      • Try specific commands for your device, like:
        • TV - [VOL UP], [VOL DOWN] and [MUTE]
        • VCR - Put a tape in and try [PLAY], [REWIND] and [FFWD]
        • DVD Player - Put a DVD in and try [PLAY], [Pause] and [FFWD]
        • Audio Device - [VOL UP], [VOL DOWN] and [MUTE]
      • If your device does not work for specific commands, repeat steps above

      Code Number Readback

        To identify the 3-digit setup code for your device, follow these steps:

        1. Press your device key, then [SEL/OK] - hold both down until the device button lights up under your finger
        2. Press [INFO] The illuminated button will “blink back” the code number, with a 1-second interval between each digit of the code
          • The number 0 will blink 10 times
          • For example: Code 405:
            • blinks 4 times
            • 1 second
            • Blinks 10 times
            • 1 second
            • Blinks 5 times

      Programming Volume Control

        By default, your remote defaults to your TV volume control (unless you are in AUDIO mode)

        To control volume commands through your CONVERTER in the remote's CABLE mode:

        1. Press [OK], then [CBL] together - hold both down until the [CBL] button lights up (under your finger)
        2. Press [VOL ], then [CBL]. The [CBL] button will blink and go out

        To control volume / mute back through your TV in the remote's CABLE mode:

        1. Press [OK], then [CBL] together - hold both down until the [CBL] button lights up (under your finger)
        2. Press [VOL ], then [TV]. The [CBL] button will blink and go out

      Installing / Replacing Batteries

        Install two (2) "AA" batteries as indicated by the diagram in the battery compartment. Be careful to properly match the "+ / -" ends of the batteries with the diagram in the battery compartment

        When the batteries become too weak to operate the remote control properly, the mode keys will become dim or not illuminate at all during use. When this happens, install 2 new "AA" size batteries

        Your remote control has Memory Guard, which eliminates reprogramming after battery changes

      General Reset

        The remote can be reset to its factory default settings if needed

        1. Press [OK], then [CBL] together until the [CBL] button lights up (under your finger)
        2. Press [1]
        3. The [CBL] button will blink 3 times and go out. All codes will now be cleared. Start programming your remote over again, as needed
        • If the [CBL] button DID NOT blink 3 times and go out, follow the alternate procedure below.

        1. Press [OK], then [CBL] together until the [CBL] button lights up (under your finger)

        2. Press [0]
        3. The [CBL] button will blink 3 times and go out. All codes will now be cleared. Start programming your remote over again, as needed

      PHAZR-5 (UR5U-9000L & UR5U-9020L)


      View printable manual


      Remote Controls for CA, OR and WA (277)

      Expand All | CollapseAll


      Program Remote Using the Popular Brands Method

        1. Turn on the equipment you wish to program (TV, DVD, AUX, or AUD)
        2. Point the remote at the device and press and hold the [OK/SEL] and TV buttons together for 3 seconds While holding the device key (TV, AUD, DVD, AUX) the LED will light off and on again
        3. Begin to press the numbers keys, one at a time, starting with 1, then 2, 3, etc until the device turns off
          #TVAudioDVDAUX
          0SANYOROTELHITACHIBOSE
          1SONYDENONSONYHP
          2SAMSUNGYAMAHAPHILIPSAPPLE / iPod
          3LGMARANTZSAMSUNGAPPLE / iPod
          4TOSHIBASONYPHILIPS MAGNAVOXMICROSOFT / XBOX
          5PANASONICINTEGRAPANASONICSONY / PS2
          6PHILIPSHARMAN KARDONLGLUTRON
          7HITACHIPIONEERJVCX-10
          8SHARPONKYODENONX-10
          9VIZIOLEXICONPIONEERMICROSOFT / XBOX
        4. If your brand does not appear in the brand chart, perform setup using either DIRECT CODE ENTRY or CODE SEARCH
        5. Press the devicebutton(TV, DVD, AUX, or AUD) to save the code
        6. The device button LED will blink twice to confirm the code is stored

      Three-Digit Code Programming Method

        1. Turn on the equipment you wish to program (TV, DVD, AUX, or AUD)
        2. Press and hold the device key (TV, AUD, DVD, AUX) and the [OK/SEL] button down together for 3 seconds until the device key stays lit
          • The device key (TV, AUD, DVD, AUX) will stay lit for 30 seconds. The next step must be entered while the LED is on
        3. Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables
          • Try the first three-digit number and wait one second for the equipment to turn off. If it doesn't, try the next three-digit number, and so on, until the device turns off

            Using TV key



            Using AUD key

            Using DVD key




            Using AUX key





        4. Press [POWER] to turn the device back on
        5. If the device does not turn back on, repeat steps 1-5
        6. Press the device key (TV, AUD, DVD, AUX) again. The device LED will blink twice to confirm that the code has been stored

      Auto Search Method

        If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:

        1. Turn on the equipment you wish to operate
        2. Press the device key (TV, AUD, DVD, AUX) and [OK/SEL] simultaneously for 3 seconds. The device key (TV, AUD, DVD, AUX) will turn on indicating that it's ready to be programmed
        3. Press [CH UP] or [CH DOWN] button and release. Do this every one second or keep the button pressed down. A new code will be entered one at a time Release the [CH UP] or [CH DOWN] button when the device turns off
        4. Press [POWER] to turn the device back on
        5. Try all of the functions of the remote control. If the buttons do not work as they should, repeat steps again

      Code Number Readback

        1. Press the device key (TV, AUD, DVD, AUX) and [OK/SEL] simultaneously for 3 seconds. The device key (TV, AUD, DVD, AUX) will turn on
        2. Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code number
        3. Each digit is separated by 1 second. Ten blinks is equal to the number 0
          • For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks

      Volume Control

        Volume and Mute control are factory programmed to the respective Device mode you select, as follows:

        • CBL : CBL
        • TV : TV
        • DVD : TV
        • AUD : AUD
        • AUX : AUX


        If you wish to store the TV volume control in CBL mode, use the following steps

        1. Press [CBL] and [OK/SEL] simultaneously for 3 seconds
        2. [CBL] will light on for 30 seconds. The next step must be entered while the LED is on
        3. Press [VOL UP]
        4. Press [TV]. [TV] will blink twice to confirm the programming

        To restore the volume control back to your TV in CBL mode, repeat the above steps by replacing [TV] with [CBL] in step 4

      Battery Info

        Install two (2) "AA" batteries as indicated by the diagram in the battery compartment. Be careful to properly match the "+ / -" ends of the batteries with the diagram in the battery compartment.

        Remote Controls for CA, OR and WA (278)

        When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.

      Memory Lock

        This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.

      Resetting The Remote

        1. Hold [CBL] and [REC] until the mode lights flash in order, should take roughly 5 seconds
        2. Reset does not cause the remote to lose its ability to control the converter

      RT-SR50 Simplicity


      View printable manual

      • RT-SR50 Simplicity

      Remote Controls for CA, OR and WA (279)

      Expand All | CollapseAll


      Programming TV using Code Entry Method

        1. Turn on the TV
        2. Press [SEL/OK] and [MUTE] together until the indicator light illuminates
        3. Enter in the code for your TV:
        4. Enter EVERY code listed until your TV turns off
        5. Test the TV by pressing [MUTE]. If the TV turns back on, the programming was successful
        6. If your TV turns back on, press [SEL/OK] to lock in the code
        7. If the TV Does not turn on, enter the next code listed until the TV turns back on and press [SEL/OK] to lock in the code

      Programming TV Using Point and Press Method

        1. Turn on the TV
        2. Press [SEL/OK] and [MUTE] together until the indicator light illuminates
        3. Press and hold [CH UP] until the TV turns off
        4. As soon as the TV turns off, release [CH UP]
        5. Test the TV by pressing [MUTE]
          • If the TV turns back on, the programming was successful. Press [SEL/OK] to lock in the code
          • If the TV Does not turn on, press [CH DOWN] until the TV turns back on and press [SEL/OK] to lock in the code

      TV Code Readback

        1. Press [TV POWER] and [SEL/OK] together until the indicator light illuminates
        2. Press [INFO] to identify your TV setup code
        3. The indicator light blinks back the code numbers with a 1-second interval between each digit
          • "0" Is indicated by 6 fast blinks
          • For example, 0-0-3-5 would blink back as:
            • 6 fast blinks
            • (one second)
            • 6 fast blinks
            • (one second)
            • 3 slow blinks
            • (one second)
            • 5 slow blinks

      Programming Volume Control

        The default volume control is done through the TV

        To program volume control to your Cable Converter:

        1. Press and [CBL POWER] and [SEL/OK] together until the indicator light illuminates
        2. Press [VOL UP], then [CBL POWER]. The indicator light will blink and go out


        To control the volume back through the TV:

        1. Press and hold the [CBL POWER] and [SEL/OK] together until the indicator light illuminates
        2. Press [VOL UP], then [TV POWER]. The indicator light will blink and go out

      Batteries

        Install two (2) new "AA" batteries as indicated by the diagram in the battery compartment.

        When the indicator light becomes dim or no longer illuminates during use, batteries need to be replaced.

      Memory Guard

        This remote has Memory guard, which eliminates reprogramming after battery changes.

      Resetting Your Remote

        To reset your remote to its default settings:

        1. Press and [CBL POWER] and [MUTE] together until the indicator light illuminates
        2. Press [1]. The indicator light will blink and go out

      Cisco Digital Transport Adapter (DTA) Remote Controls 270/271


      Printable manuals (271 (HDA-RF 2.2), 270 (HDA-IR 2.2))

      • DTA Remote Controls 270/271

      Remote Controls for CA, OR and WA (280)

      Expand All | CollapseAll


      Identifying the 270 vs. 271

        These remotes are identical.

        The model numbers are stamped on the back The 271 (IR/RF model) is listed as HDA-RF 2.2 The 270 is listed as HDA-IR 2.2

        Remote Controls for CA, OR and WA (281)

      Auto-Search Programming (recommended)

        1. Turn on your TV
        2. Point the remote control at the DTA
        3. Press and hold the Prog button for three seconds until the LED turns on
        4. Press and hold the [CH+] button search for codes
          • A new code transmits every 1.5 seconds, and the LED will blink for each one
        5. When your TV turns off, the remote control has found a valid code
        6. Press the TV button to store the code
        7. To test, press TV Power

      Manual Programming Method

        1. Find your device codes in the manual
        2. Turn on your TV
        3. Point the remote control at the DTA
        4. Press and hold the Prog button for three seconds until the LED turns on
        5. Press and hold the [TV] button. The LED will blink once and remain on
        6. Enter the code for your brand
        7. If the code is valid, the LED will blink twice and the code will be retained
        8. If the code is invalid, the LED will blink three times, and remain in programming mode. Try another code on the list
        9. Press the TV button to test. the TV should turn off

      Pairing the 271 Remote - RF Mode

        1. Press and hold the [Prog] button for three seconds until the LED turns on
        2. Press the [Info] key
        3. The LED on the remote will blink slowly indicating that the device is in pairing mode
        4. Enter the 3 digits the DTA shows on-screen The DTA will acknowledge the 3 digits entered was correct

      Unpairing the 271 Remote

        1. Press and hold the Prog button for three seconds until the LED turns on
        2. Press 9, 8, 7

        3. The LED will blink 2 times quickly

      Volume Control

        By default the remote controls the volume and mute on the DTA, not the TV

        To control the volume and mute on the TV:

        1. Press and hold the [Prog] button for three seconds until the LED turns on
        2. Press the [Vol+] button

        To control the volume and mute back to the DTA:

        1. Press and hold the [Prog] button for three seconds until the LED turns on
        2. Press the [Vol-] button

      Synergy V (RC-U62SD)


      View printable manual

      • Synergy V (RC-U62SD)

      Remote Controls for CA, OR and WA (282)

      Expand All | CollapseAll


      Programming Your Cable Converter

        Your remote control is pre-programmed to operate the Scientific Atlanta and Motorola Digital / DVR set-top terminals. Therefore, no further programming of your Cable devices is necessary.

      Programming Other Devices

        1. Turn on your device
        2. Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence:

          Remote Controls for CA, OR and WA (283)

        3. From the Setup Code list below, locate and enter the 3-digit code for your brand. If multiple codes are listed, you may have to enter several 3-digit codes until your device turns off
          • If you cannot find your code, you can use Point and Press Programming
        4. Press [MUTE]
        5. If your device turns back on, press [OK] to lock in the code
          • The mode (power) buttons will blink 3 times and go out
        6. Use your device key (MOT, AUDIO, VIDEO, TV, S-A) to power the device back on If your device does not turn back on, repeat steps using a different setup code
        7. Try specific commands for your device, like:
          • TV - [VOL UP], [VOL DOWN] and [MUTE]
          • VCR - Put a tape in and try [PLAY], [REWIND] and [FFWD]
          • DVD Player - Put a DVD in and try [PLAY], [Pause] and [FFWD]
          • Audio Device - [VOL UP], [VOL DOWN] and [MUTE]
        8. If your device does not work for specific commands, repeat steps using a different setup code

        9. Write your device brand & setup code for future reference

      Point and Press Programming

        1. Turn on your device
        2. Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence:

          Remote Controls for CA, OR and WA (284)

        3. Press and hold the [CH +] button until the TV turns off
        • Every time the buttons light in a sequence, the remote is trying a different code. It may take seconds or several minutes for the remote to find the proper code for your device
        • Please be patient, and be ready to release the [CH +] button when the device turns off
      • Press [MUTE]
        • If your TV turns back on, press [OK] to lock in the code. The mode (power) buttons will blink 3 times and go out
        • If your TV does not run back on, try pressing [CH -] one step at a time until that device turns back on. Each time you press the [CH -] button, the power/mode buttons will start blinking in reverse sequence:

          Remote Controls for CA, OR and WA (285)

      • Once you have found the proper code, press [OK] to lock in the code
      • Try specific commands for your device, like:
        • TV - [VOL UP], [VOL DOWN] and [MUTE]
        • VCR - Put a tape in and try [PLAY], [REWIND] and [FFWD]
        • DVD Player - Put a DVD in and try [PLAY], [Pause] and [FFWD]
        • Audio Device - [VOL UP], [VOL DOWN] and [MUTE]
      • If your device does not work for specific commands, repeat steps above

      Code Number Readback

        To identify the 3-digit setup code for your device, follow these steps:

        1. Press your device key (Audio, Video, or TV), then [SEL/OK] - hold both down until the device button lights up under your finger
        2. Press [INFO] The illuminated button will “blink back” the code number, with a 1-second interval between each digit of the code
          • The number 0 will blink 10 times
          • For example: Code 405:
            • blinks 4 times
            • 1 second
            • Blinks 10 times
            • 1 second
            • Blinks 5 times

      Buttton Functions

        Remote Controls for CA, OR and WA (286)

      Installing / Replacing Batteries

        Install two (2) "AA" batteries as indicated by the diagram in the battery compartment. Be careful to properly match the "+ / -" ends of the batteries with the diagram in the battery compartment

        When the batteries become too weak to operate the remote control properly, the mode keys will become dim or not illuminate at all during use. When this happens, install 2 new "AA" size batteries

        Your remote control has Memory Guard, which eliminates reprogramming after battery changes

      General Reset

          1. Press [S-A] or [MOT], then [SEL/OK] together until the [S-A] or [MOT] button lights up (under your finger)
          2. Press [0]
          3. The [S-A] or [MOT] button will blink 3 times and go out
          4. All codes will now be CLEARED. Start programming your Synergy V over again, as needed

        Synergy V (RTU60C)


        View printable manual

        • Synergy V (RTU60C)

        Remote Controls for CA, OR and WA (287)

        Expand All | CollapseAll

        Your remote control is pre-programmed to operate the Scientific Atlanta and Motorola Digital / DVR set-top terminals. Therefore, no further programming of your Cable device is necessary.

        Three-Digit Code Programming Method

          1. Turn on the equipment you wish to program. (TV, VCR, or AUX)
          2. Press [SEL], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence:
            Remote Controls for CA, OR and WA (288)
          3. From the TV Setup Code list below, locate and enter the 3-digit code for your brand. If multiple codes are listed, you may have to enter several 3-digit codes until your TV turns off

            TV -- >

            VCR -- >

            DVD (VCR key) -- >

            For TV/VCR combos, program the TV code first, then the VCR code

            For TV/DVD combos, program the TV code first, then the DVD code

            CD Player (AUDIO key) -- >

            Receiver/Amplifier (AUDIO key) -- >


            If you cannot find your code, you can use Point and Press ® Programming

          4. Press [MUTE]. If your TV turns back on, press [SEL] to lock in the code. The mode (power) buttons will blink 3 times and go out.
            If your TV does not turn back on, repeat steps 3 and 4 until you can turn your TV off and on

          Please Note:

          • Try all the functions on the remote control. If any of the functions do not work as they should, repeat from Step 2 using the next three-digit code number from the same brand list

        Point and Press® Programming

          This method allows you to program the remote control without using codes

          Please note:

          • The order in which you program your devices IS NOT important
          • While the remote is searching for the correct setup code, other devices that you are NOT currently programming may turn on/off. This is nothing to be concerned about. Simply continue pressing [CH +] until you find the correct code for the device you are programming. Your other devices will not be affected
          1. Turn on your Device
          2. Press [SEL], then [MUTE] together - hold both buttons down until the lighted mode (power) buttons start blinking in sequence:

            Remote Controls for CA, OR and WA (289)

          3. Press and hold the [CH+] button until the TV turns off

            Every time the mode (power) buttons light in a sequence (see animation below), the remote is trying a different code. It may take seconds or several minutes for the remote to find the proper code for your device. Please be patient, and be ready to release the [CH +] button when the device turns off:

            Remote Controls for CA, OR and WA (290)

          4. As soon as the device turns off, release [CH +]
          5. If your TV does not run back on, try pressing [CH -] one step at a time until that device turns back on. Each time you press the [CH -] button, the power/mode buttons will start blinking in reverse sequence:

            Remote Controls for CA, OR and WA (291)

          6. Once you have found the proper code, press [SEL] to lock in the code

        Code NumberReadback

          To identify the 3-digit setup code for your TV, follow these steps:

          1. Press [TV], then [SEL] - hold both down until the [TV] button lights up under finger
          2. Press [INFO]. The illuminated button will “blink back” the code number, with a 1-second interval between each digit of the code

            Example: For code “105”, the remote will blink 1 time, then 10 times, then 5 times

          To identify the 3-digit setup code for your VIDEO device, follow these steps:

          1. Press [VIDEO], then [SEL] - hold both down until the [VCR] button lights up under finger
          2. Press [INFO]. The illuminated button will “blink back” the code number, with a 1-second interval between each digit of the code

            Example: For code “105”, the remote will blink 1 time, then 10 times, then 5 times

          To identify the 3-digit setup code for your AUDIO Device, follow these steps:

          1. Press [AUDIO], then [SEL] - hold both down until the [AUDIO] button lights up under finger
          2. Press [INFO]. The illuminated button will “blink back” the code number, with a 1-second interval between each digit of the code


            Example: For code “105”, the remote will blink 1 time, then 10 times, then 5 times

        ALL POWER Smart Key

          Programming and using the[ALL POWER] SmartKey®
          The [CBL] button normally turns on / off your CABLE converter. But you can make it do more than that!

          IMPORTANT:
          You must first program ALL devices on your Synergy V for the [ALL POWER] SmartKey™ to work correctly

          1. Press [POWER], then [MENU] together – hold both down together until the [CBL] button illuminates
          2. Press the option Number below for the desired functions:
            If you select... When you press the [CBL] button in CABLE mode, here is what will happen...
            1 The converter & TV* will turn on, and the TV will turn to channel 3
            2 The converter & TV*will turn on, and the TV will turn to channel 2
            3 The converter & TV* will turn on, and the TV will turn to channel 4
            4 The converter, TV, and VCR* will turn on, and the TV will turn to channel 3
            5 The converter, TV, and VCR* will turn on, and the TV will turn to channel 2
            6 The converter, TV, and VCR* will turn on, and the TV will turn to channel 4
            7 The converter, TV, VCR, & AUDIO* will turn on, and the TV will turn to channel 3
            8 The converter, TV, VCR, & AUDIO* will turn on, and the TV will turn to channel 2
            9 The converter, TV, VCR, & AUDIO* will turn on, and the TV will turn to channel 4
            0 The converter (only) will turn on. This is the default setting
          3. The [CBL] button will blink and go out, storing the selected option.

          Using the[ALL POWER] SmartKey®

          • When using the [ALL POWER] SmartKey®, be sure to keep your remote aimed at the devices to ensure all functions are received in their entirety
          • Whenever the [ALL POWER] SmartKey® is pressed the mode of the remote control willautomatically switch back to CABLE

        Volume Control

          After you program your remote:

          When your Remote is in this mode... Your volume/mute is controlled through ...
          CBL Your TV (default)
          TV Your TV (default)
          AUDIO Your Audio Device (default)
          VIDEO Your TV (default)

          To control volume / mute through your

          Converter in the remote's [CBL] mode:

          1. Press [SEL], then [CBL] together - hold both down until the [CBL] button lights up (under finger)
          2. Press [VOL+], then [CBL]. The [CBL]button will blink and go out

          To control volume / mute back through your TV in the remote's CABLE mode:

          1. Press [SEL], then [CBL] together - hold both down until the [CBL] button lights up (under finger)
          2. Press [VOL+], then [TV]. The [CBL] button will blink and go out

        Mode Lock

          Your Synergy V remote comes locked in it's CABLE operating mode. While it is in [CBL] mode, it can control all set-top operations, as well as power in the TV, VIDEO, and AUDIO devices

          To operate more functions on your TV, VIDEO, and AUDIO devices, you can unlock the remote as follows:

          1. Press [MUTE], then [CBL] together. Hold BOTH buttons down until the [CBL] button lights up (under finger)
          2. Press [9,9,9]. The [CBL] button will blink and go out

          To lock your remote back in it's CABLE operating mode:

          1. Press [MUTE], then [CBL] together. Hold BOTH buttons down until the [CBL] button lights up (under finger)
          2. Press [0,0,0]. The [CBL] button will blink and go out

        INPUT Button

          Remote Controls for CA, OR and WA (292)

          This button changes the input source of your electronic device

          • In the remote's [CBL] mode (default), This operates a converter function
          • In the remote's TV mode, the button changes the input source of the TV (Input 1, Input 2, Aux, Game, Video 1, Video 2, etc)
          • In the remote's VCR mode, it changes the TV/VCR input on your VCR

          You can program this button so that in the remote's CABLE mode, the [INPUT] button will operate the input function of your TV or VCR

          • To program [INPUT] to operate the TV input in your remote's [CBL] mode, follow these steps:

            1. Press [INPUT], then [SEL]

              together

              until the [CBL] button lights up

            2. Press [TV]. The [CBL] button will blink 3 times and go out

          • To program [INPUT] to operate the VCR input in your remote's [CBL] mode, follow these steps:

            1. Press [INPUT], then [SEL]

              together

              until the [CBL] button lights up

            2. Press [VIDEO]. The [CBL] button will blink 3 times and go out

          • To program [INPUT] to return to defaults:

            1. Press [INPUT], then [SEL]

              together

              until the [CBL] button lights up

            2. Press [CBL]. The [CBL] button will blink 3 times and go out

        General Reset

          Depending on the manufacturer date of the remote, it can be reset to its factory default settings.

          1. Press [CBL], then [SEL] together until the [CBL] button lights up (under finger)
          2. Press [SETTINGS], then [SETTINGS] again. The [CBL] button will blink 3 times and go out
          3. All codes will now be CLEARED. Start programming your Synergy® V over again, as needed

        URC1056 (OCAP)


        View printable manual

        • URC1056 (OCAP)

        Remote Controls for CA, OR and WA (293)

        Expand All | CollapseAll


        Programming Devices into the URC1056 Remote

          Note:

          • For control of a Combo device (for example, a TV/VCR combo), skip this section and perform the instructions on Setting Up a Combo Unit

          • These instructions assume you have already selected the proper device code(s)

          1. Turn on the device
          2. Press and hold the appropriate device key until it blinks once
            VCR VCR, PVR, DVR or extra DVD Player
            DVD DVD Player, or extra VCR, TV/VCR Combo or PVR
            AUD Audio Amplifier, Tuner, or Receiver
            TV Television
            CBL Cable Box (Converter) or Satellite Receiver
          3. Press and hold the SETUP key until it blinks twice
          4. Enter in the code for the device:Audio Amplifiers -- >

            Audio Receivers -- >

            Audio Accessories -- >

            DVD Players -- >

            DVD Recorders -- >

            DVD Combos -- >

            DVR/PVR Systems -- >

            TVs -- >

            DLP TVs -- >

            HDTVs -- >

            LCD TVs -- >

            VCR -- >

            The mode keys should then blink twice if the code was accepted.
            If the selected mode key emits a long blink, the entry is invalid. Repeat steps 2 through 4 and try entering the same code again.

          5. Test the device by pressing PWR. If the device responds, the program was successful
          6. If the device does not respond, repeat steps 2-4 for other codes (if applicable)

        Setting Up aCombo Unit:

          If you own a combo unit such as a TV/VCR Combo or a TV/DVD Combo, you need to follow special steps to set it up. Perform the following instructions to control a combo device:

          1. For a TV/VCR or TV/DVD Combo, turn on your Combo unit and insert a video cassette (or a DVD)
          2. On the remote control, press VCR (or DVD) once ; it will blink once. Then press and hold SETUP until the VCR key blinks twice
          3. Use the Manufacturer’s Codes below to locate the brand name and enter the first four-digit codeTV/DVD Combos controlled by TV -- >

            TV/DVD Combos controlled by DVD -- >

            TV/VCR Combos controlled by TV -- >

            TV/VCR Combos controlled by VCR -- >

            TV/VCR/DVD Combos controlled by TV -- >

            TV/VCR/DVD Combos controlled by DVD -- >

            TV/VCR/DVD Combos controlled by VCR -- >

          4. If you perform this procedure correctly, the VCR key will blink twice

            NOTE: If the VCR key did not blink twice after entering the codes last digit, repeat steps 2 through 4 and try entering the same code again.

            If you’ve located a setup code that works for your combo device (for example, a TV/VCR Combo) and a separate TV code is also listed, you’ll need to program this code into the remote control to access volume control (see “Programming Device Control”)

        Searching forCodes

          If your home entertainment device does not respond to the Atlas OCAP 5-Device Remote Control after trying all of the codes listed for your brand, or if your brand is not listed at all, try searching for your code.

          For example, to search for a code for your TV:

          1. Turn on your TV
          2. On the remote control, press TV once; it will blink once. Then press and hold SETUP until the TV key blinks twice
          3. Using the remote keypad, press 9, 9, 1. The mode keys will blink twice
          4. Aim the remote control at the TV and press PWR once

            NOTE: In the search mode, the remote control will send IR codes from its library to the selected device, starting with the most popular code first

          5. Press PWR. The TV should turn on, then press SETUP to lock in the code
          6. If the TV does not turn on during step 5, then slowly press and release CH- to go back through the codes, then press SETUP when the TV turns on

        Code Number Read Back:

          If you have set up the Atlas OCAP 5-Device Remote Control by searching for your device code (on the previous page), you may need to find out which four digit code is operating your equipment.

          For example, to find out which code is operating your TV:

          1. On the remote control, press TV once; it will blink once. Then press and hold SETUP until the TV key blinks twice.
          2. Enter 9, 9, 0. The TV key will blink twice.
          3. To view the code for the first digit, press 1 once. Count the number of times the TV key blinks (e.g., 3 blinks = 3)

            NOTE: If a code digit is 0, the selected mode key will not blink.

          4. Repeat step 3 three more times for the remaining digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit
          5. To check for other device codes, repeat steps 1 through 4, but substitute the appropriate key (e.g., VCR, DVD, AUD, or CBL) for the device you are checking

        Channel Control Lock

          By default, the remote control’s channel-control capabilities are locked to the cable converter. The affected keys* are 1 through 0, CH+, CH-, and LAST. This will guarantee that you do not inadvertently change a channel on your TV or VCR. However, you can deactivate this feature to allow full access to these keys in the TV and VCR modes

          *NOTE: This feature does not affect the AUD mode.

          Unlocking Channel Control

          1. On the remote control, press CBL once; it will blink once. Press and hold SETUP until the CBL key blinks twice
          2. Enter 9, 7, 3. The CBL key will blink twice
          3. Press CH- once. The CBL key will blink four times

            Now the remote control will provide TV and VCR channel-control capabilities while in the TV or VCR mode.

        Locking Channel Control to CBL

          1. On the remote control, press CBL once; it will blink once. Press and hold SETUP until the CBL key blinks twice
          2. Enter 9, 7, 3. The CBL key will blink twice
          3. Press CH+ once. The CBL key will blink four times

            Now, regardless of what mode you select (except AUD), the channel keys will only change channels on your cable converter

        Volume Lock

          Volume Lock allows you to control the volume through the device identified as having your primary speaker(s), regardless of which mode you are using. On the Atlas OCAP 5-Device Remote Control, Global Volume Lock is set to TV, so you can control TV volume while in the VCR, DVD, TV or CBL mode. You can perform Individual Volume Unlock on a selected device to set its volume control for independent operation.

          NOTE: The audio mode’s (AUD) volume controls are active regardless of Volume Lock settings. However, if you lock the volume controls to the AUD mode, you will have control of the audio device’s volume in all other modes (i.e., VCR, DVD, TV, and CBL). This can be an advantage if, for example, you always listen to home entertainment devices through your receiver’s speakers.

          Unlocking Volume Control for a Single Device (Individual Volume Unlock)

            1. Assuming Global Volume Lock is active, select a mode on the remote control that you want to unlock (e.g., CBL) and press it once. Next, press and hold SETUP until the device key blinks twice
            2. Enter 9, 9, 3. The last-selected device key will blink twice
            3. Press VOL- once. The last-selected device key will blink four times
            4. Repeat steps 1 through 3 for each device you want volume to be unlocked

              Now, after you select a device that has volume unlocked (e.g., CBL), pressing VOL+, VOL-,or MUTE, will control only that device’s volume.

          Unlocking All Volume Control (Global Volume Unlock)

            NOTE: Performing these instructions will set independent volume control for all programmed devices.

            1. On the remote control, press and hold SETUP until the last-selected device key blinks twice
            2. Enter 9, 9, 3. The last-selected device key will blink twice
            3. Press VOL+ once. The last-selected device key will blink four times

          Locking Volume Control To One Mode (Global Volume Lock)

            NOTE: The audio mode’s volume controls are active regardless of Volume Lock settings. However, if you lock the volume controls to the AUD mode, you will control the audio device’s volume in all other modes (i.e., VCR, DVD, TV, or CBL). This can be an advantage if, for example, you always listen to home entertainment devices through your receiver’s speakers.

            1. On the remote control, press and hold SETUP until the last-selected device key blinks twice
            2. Enter 9, 9, 3. The last-selected device key will blink twice
            3. Select a mode (e.g., TV or AUD) which you want to use to control the volume. The selected device key will blink twice

              Now, when you press VOL+, VOL-,or MUTE, the volume of the selected device (e.g., TV) is controlled regardless of mode

        Cable ID Lock

          The Atlas OCAP 5-Device Remote Control is locked at the factory to operate your cable provider’s set top box. However, if you have another brand or model of cable converter or satellite service that you would like to control, then you’ll need to perform the following steps to unlock the ID Lock, enter a new manufacturer’s code, and lock the ID Lock again

          1. Turn on the cable converter
          2. On the remote control, press CBL once; it will blink once. Then press and hold SETUP until the CBL key blinks twice
          3. Enter 9, 8, 2. The CBL key will blink four times, indicating ID Lock is unlocked
          4. Perform the instructions under “Programming Device Control” to program device control for the desired cable converter or satellite receiver. When you are done, perform steps below to again lock the cable ID Lock
          5. On the remote control, press CBL once; it will blink once. Then press and hold SETUP until the CBL key blinks twice
          6. Enter 9, 8, 2. The CBL key will blink twice, indicating ID Lock is again locked

        Macro Keys

          The Atlas OCAP 5-Device Remote Control includes two macro keys (located directly below the MUTE and LAST keys). Macro keys allow you to set up key macros to activate certain keys in a specific order.

          For example, you can set up a key macro to change the channels on your TV, raise or lower the volume, and start recording on your VCR, all with the touch of one key. If you want to change the macros stored in a previously-programmed macro key, you’ll need to clear the key first (see “Clearing a Macro Key”.

          Programming a Macro Key

            1. On the remote control, press and hold SETUP until it blinks twice
            2. Enter 9, 9, 5. The SETUP key blinks twice
            3. Select a macro key (for example, F1) and press it once
            4. Press the key sequence you want to program into the macro. For example, to turn on your TV and raise its volume, press TV followed by VOL+

              NOTE: You can program up to 15 key presses into one macro

            5. Press and hold SETUP until it blinks twice
            6. To add another macro, repeat steps 1 through 5, substituting the new key sequence to be added in step 4.

              NOTE: Programming more than five macros on the same macro key overwrites previous settings.

          Clearing a Macro Key

            1. On the remote control, press and hold SETUP until it blinks twice
            2. Enter 9, 9, 5. The SETUP key blinks twice
            3. Press the macro key you want to clear once
            4. Press and hold SETUP until it blinks twice

              This macro key is now clear and ready for reprogramming.

        Master Power Key

          The Atlas OCAP 5-Device Remote Control has a unique feature that allows you to sequentially turn up to five of your home entertainment devices on or off with a single key press.

          NOTE: MASTER POWER (PWR) only works in the CBL mode. If it is not programmed, only the cable converter will turn on or off. In any other mode, pressing MASTER POWER (PWR) once will turn the selected device on or off.

          Programming the Master Power Key

          1. On the remote control, press and hold SETUP until the last-selected device key blinks twice
          2. Enter 9, 9, 5. The last-selected device key blinks twice
          3. Press PWR once
          4. For the first device you want in the power on sequence, press a device key (e.g., CBL) once. Then press PWR once. For the second device in the power sequence, press its key once (e.g, TV). Then press PWR
          5. Repeat step 4 up to four more times to add the second, third, fourth, and fifth device, as desired
          6. To save the settings and exit the program:
            1. Press CBL once.
            2. Press and hold SETUP until the CBL key blinks twice.

          Using the Master Power Key

            1. After programming, point the remote control at the devices. Press CBL once
            2. Press PWR once to sequentially turn the programmed home entertainment devices on or off

              You will see the devices turn on or off according to the programmed sequence

          Clearing the Master Power Key

            1. On the remote control, press and hold SETUP until the last-selected device key blinks twice
            2. Enter 9, 9, 5. The last-selected device key blinks twice
            3. Press and release PWR
            4. Press and hold SETUP until the CBL key blinks twice

        Re-Assigning Device Keys

          The Atlas OCAP 5-Device Remote Control can be set up to control a second device of an already-assigned type. For example, to have the unit control a TV, a Cable Converter, and two audio devices (for example, two audio receivers), re-assign the unused VCR key to operate the second audio device as follows:

          NOTE: VCR is preset at the factory to control an RCA VCR. Performing the steps below will overwrite those settings.

          1. On the remote control, press VCR once; it will blink once. Then press and hold SETUP until the VCR key blinks twice
          2. Enter 9, 9, 2. The VCR key will blink twice
          3. Press AUD once, then press VCR once. The VCR key will blink twice

          The VCR key is now ready to be programmed for your second audio device. See “Programming Device Control”. To re-assign other device keys, repeat these and substitute the key sequence using the following chart:

          NOTE: Only one device can be assigned to an unused device key at a time.

          To Re-Assign Perform Key Sequence
          VCR as 2nd AUD key VCR, SETUP, 9, 9, 2, AUD, VCR
          VCR as 2nd TV key VCR, SETUP, 9, 9, 2, TV, VCR
          VCR as 2nd CBL key VCR, SETUP, 9, 9, 2, CBL, VCR
          VCR back to VCR VCR, SETUP, 9, 9, 2, VCR, VCR

          To re-assign another unused device key, substitute it for the VCR key above and then perform the sequence. For example, to re-assign an unused AUD key as a second DVD key, perform AUD, SETUP, 9, 9, 2, DVD, AUD

          When a re-assignment is done, the selected device key (e.g., AUD) will blink twice to confirm your choice. At that time, you will need to program device control (see “Programming Device Control”)

        Activating Backlighting(Optional Models)

          On some models of your Atlas OCAP 5-Device Remote Control, you can activate backlighting. Backlighting enables your remote’s keypad to remain lit for five seconds after you press any key.

          To enable backlighting on a remote with that feature, perform the following step:

          1. Press SETUP twice within one second. Backlighting is turned on.

          To disable backlighting, perform the following step:

          1. Press SETUP twice within one second. Backlighting is turned off

        Clearing Custom Programming

          The Atlas OCAP 5-Device Remote Control contains a Custom Programming Reset program. You can use it to remove all custom programming, except your setup codes and reassigned device keys

          IMPORTANT: Executing this program will erase all custom settings for Volume Lock, Learned Keys, Tune-In Keys, and Channel Lock. However, your device programming remains

          1. On the remote control, press and hold SETUP until the last-selected device key blinks twice
          2. Enter 9, 8, 0. The last-selected device key blinks twice, pauses, and blinks twice again to confirm that all custom programming is cleared

        ENT 8000


        View printable manual

        • ENT 8000

        Remote Controls for CA, OR and WA (294)

        Expand All | CollapseAll


        Automatic Programming

          The SmartScan™ programming instructions can also be found on the battery cover of the remote control. SmartScan™ will allow you to easily try all the available programming codes for the selected device and find the best match. If you prefer manual programming or already have the device codes see the Manual Programming section below

          1. Turn on the device
          2. Pressing and hold the desired device key (AUX, AUD, VCR, CBL, DVD, TV) until all device keys on the remote begin to flash
            (approximately 3 seconds), then release the key
          3. If the device you’re are attempting to program matches the selected device key (e.g. TV = TV key) proceed to step 5.
          4. If the device you’re are attempting to program does not match the selected key (e.g. a second VCR = AUX key), locate the correct prefix code for the device you wish to program (listed below). Press and release the number key that matches the prefix code
            Prefix: Device:
            0 Television
            1 DVD Player, VCR, or PVR
            4 Audio Device
            5 Combo Units
          5. Press and release the POWER key. The device key will stop flashing and remain on
          6. Point the remote control at the selected device
          7. Press and hold the ? key until the device turns off. While holding the ? key the remote will send a new code approximately once every second. The device button will blink each time a new code is sent. If you pass the code that turns off the device, press the ? key to return to the previous code
          8. When the device turns off, you have found a candidate code. Press the POWER Key to turn device back on. Test various functions using the remote control to determine if this code will work. If primary functions do not work, make sure the device is still on then resume SmartScan™ by pressing the ? key to find another device code
          9. Once you have found a satisfactory code, press OK to lock the code. The power of the device must be on. The device key will then flash three times. Go to section 10 to recall and record your device codes. When all the codes have been attempted the device button will flash rapidly

        Manual Programming

          To manually set up the Enterprise to operate a device, find the manufacturer of the device in the list of manufacturers’ codes

          1. Press and hold the device key to be programmed until all device keys begin to flash (approximately 3 seconds). Release the key. The selected device key will continue to flash
          2. Enter the four digit code for the desired device using the number keys. After pressing the first digit, the device key should light and remain on if the programming is successful. After the last digit is pressed the device key should flash three times and turn off

            Audio Device -- >

            TV/DVD & TV/VCR Combos -- >

            TV -- >

            VCR/DVD/PVR -- >

          3. Test the code by trying various functions. If the primary function keys fail to respond satisfactorily try the next code listed for the manufacturer.

            If you have tried all the codes listed for the manufacturer and the device does not respond, try to program the device using Automatic Programming above

        Recalling aDevice Code

          Use the following steps to read the code set for a device. This is useful for determining a device code that was set using Automatic Programming above

          1. Press and hold the device key to be read until all device keys begin to flash (approximately 3 seconds). Release the key. The selected device key will continue to flash
          2. Press and release the OK key. The device key flashes each of the four digits in the code. A pause separates each digit. For example, three flashes represent the number 3, and a rapid flicker represents 0. A code of 1032 will be shown as:

            FLASH <pause> FLICKER <pause> FLASH, FLASH, FLASH <pause> FLASH, FLASH

            Count and record the sequence of flashes to determine the four-digit code.

        ProgrammingVolume Control

          By default, your Enterprise remote controls cable volume through the Cable Box, and the VCR and DVD through the Television. To allow volume control through a different device:

          1. Press and hold the CBL device key until all the device keys begin to flash. Release the CBL key. The CBL key will continue to flash
          2. Press and release the VOLUME ? key, the CBL key will remain on
          3. Press and release the VOLUME ? key. The CBL key will turn off when VOLUME ? is pressed, and will turn on when released
          4. Press and release the key corresponding to the device you wish to use to control volume (TV or AUD). After you release the key, the CBL key will flash three times and turn off

          To return volume control to the default state:

          1. Press and hold the CBL device key until all the device keys begin to flash. Release the CBL key. The CBL key will continue to flash
          2. Press and release the VOLUME ? key. The CBL device key will stop flashing and stay on
          3. Press and release the VOLUME ? key, and then press and release the OK key
          4. After you release the OK key, the CBL device key will flash three times and turn off

        Master PowerControl

          The Master Power function allows you to turn off and on two or more devices simultaneously with a single press of the POWER button. The following steps describe how to program the Master Power Control function:

          1. Press and hold the CBL device key until all the device keys begin to flash. Release the CBL key. The CBL key will continue to flash
          2. Press and release the POWER key
          3. Individually press and release each device key corresponding to the components you wish to be controlled by Master Power (starting with the cable device key).

            NOTE: If no keys are pressed in this step, no change will occur


          4. Press and release the POWER key. The CBL key will flash three times and turn off
          5. Manually turn on all devices. Then test the Master Power control by pressing the POWER key

          To disable Master Power, repeat the previous steps selecting only one device for Master Power (any device can be selected). The remote will now control the power ON/OFF of each device separately.

          NOTE: Once Master Power has been programmed for two or more devices, pressing the POWER key in normal operation will cause the remote to transmit the POWER on/off commands for those devices selected during Master Power programming.

          To override this and transmit a POWER on/off command for a device not included in the Master Power selection, press the DEVICE key for that device and immediately press the POWER key.

        Channel Lock

          Channel Lock causes channel up and down functions to always operate the settop box independent of the device (TV, CBL, VCR, DVD or AUD) currently selected. The remote comes with Channel Lock activated. If you want the remote control to operate the channel function on your TV or VCR, you will need to deactivate Channel Lock:

          1. Press and hold the CBL device key until all the device keys begin to flash (approximately 3 seconds). Release the CBL key. The CBL key will
            continue to flash
          2. Press and release the CHANNEL ? key
          3. Press and release the CHANNEL ? key
          4. Press the OK key. The CBL device key will flash three times to confirm

          Repeat these steps to reactivate Channel Lock

        Button Descriptions

          Remote Controls for CA, OR and WA (295)

        ENT-6412


        View printable manual

        • ENT-6412

        Remote Controls for CA, OR and WA (296)

        Expand All | CollapseAll


        Automatic Programming

          The SmartScan™ programming instructions can also be found on the battery cover of the remote control. SmartScan™ will allow you to easily try all the available programming codes for the selected device and find the best match. If you prefer manual programming or already have the device codes see the Manual Programming section below

          1. Turn on the device
          2. Pressing and hold the desired device key (AUX, AUD, VCR, CBL, DVD, TV) until all device keys on the remote begin to flash
            (approximately 3 seconds), then release the key
          3. If the device you’re are attempting to program matches the selected device key (e.g. TV = TV key) proceed to step 5.
          4. If the device you’re are attempting to program does not match the selected key (e.g. a second VCR = AUX key), locate the correct prefix code for the device you wish to program (listed below). Press and release the number key that matches the prefix code
            0 Television
            1 DVD Player, VCR, or PVR
            4 Audio Device
            5 Combo Units

          5. Press and release the POWER key. The device key will stop flashing and remain on
          6. Point the remote control at the selected device
          7. Press and hold the ? key until the device turns off. While holding the ? key the remote will send a new code approximately once every second. The device button will blink each time a new code is sent. If you pass the code that turns off the device, press the ? key to return to the previous code
          8. When the device turns off, you have found a candidate code. Press the POWER Key to turn device back on. Test various functions using the remote control to determine if this code will work. If primary functions do not work, make sure the device is still on then resume SmartScan™ by pressing the ? key to find another device code
          9. Once you have found a satisfactory code, press OK to lock the code. The power of the device must be on. The device key will then flash three times. Go to section 10 to recall and record your device codes. When all the codes have been attempted the device button will flash rapidly

        Manual Programming

          To manually set up the Enterprise to operate a device, find the manufacturer of the device in the list of manufacturers’ codes

          1. Press and hold the device key to be programmed until all device keys begin to flash (approximately 3 seconds). Release the key. The selected device key will continue to flash
          2. Enter the four digit code for the desired device using the number keys. After pressing the first digit, the device key should light and remain on if the programming is successful. After the last digit is pressed the device key should flash three times and turn off

            Audio Device -- >

            TV/DVD & TV/VCR Combos -- >

            TV -- >

            VCR/DVD/PVR -- >

          3. Test the code by trying various functions. If the primary function keys fail to respond satisfactorily try the next code listed for the manufacturer.

            If you have tried all the codes listed for the manufacturer and the device does not respond, try to program the device using Automatic Programming above

        Recalling aDevice Code

          Use the following steps to read the code set for a device. This is useful for determining a device code that was set using Automatic Programming above

          1. Press and hold the device key to be read until all device keys begin to flash (approximately 3 seconds). Release the key. The selected device key will continue to flash
          2. Press and release the OK key. The device key flashes each of the four digits in the code. A pause separates each digit. For example, three flashes represent the number 3, and a rapid flicker represents 0. A code of 1032 will be shown as:

            FLASH <pause> FLICKER <pause> FLASH, FLASH, FLASH <pause> FLASH, FLASH

            Count and record the sequence of flashes to determine the four-digit code.

        ProgrammingVolume Control

          By default, your Enterprise remote controls cable volume through the Cable Box, and the VCR and DVD through the Television. To allow volume control through a different device:

          1. Press and hold the CBL device key until all the device keys begin to flash. Release the CBL key. The CBL key will continue to flash
          2. Press and release the VOLUME ? key, the CBL key will remain on
          3. Press and release the VOLUME ? key. The CBL key will turn off when VOLUME ? is pressed, and will turn on when released
          4. Press and release the key corresponding to the device you wish to use to control volume (TV or AUD). After you release the key, the CBL key will flash three times and turn off

          To return volume control to the default state:

          1. Press and hold the CBL device key until all the device keys begin to flash. Release the CBL key. The CBL key will continue to flash
          2. Press and release the VOLUME ? key. The CBL device key will stop flashing and stay on
          3. Press and release the VOLUME ? key, and then press and release the OK key
          4. After you release the OK key, the CBL device key will flash three times and turn off

        Master PowerControl

          The Master Power function allows you to turn off and on two or more devices simultaneously with a single press of the POWER button. The following steps describe how to program the Master Power Control function:

          1. Press and hold the CBL device key until all the device keys begin to flash. Release the CBL key. The CBL key will continue to flash
          2. Press and release the POWER key
          3. Individually press and release each device key corresponding to the components you wish to be controlled by Master Power (starting with the cable device key).

            NOTE: If no keys are pressed in this step, no change will occur


          4. Press and release the POWER key. The CBL key will flash three times and turn off
          5. Manually turn on all devices. Then test the Master Power control by pressing the POWER key

          To disable Master Power, repeat the previous steps selecting only one device for Master Power (any device can be selected). The remote will now control the power ON/OFF of each device separately.

          NOTE: Once Master Power has been programmed for two or more devices, pressing the POWER key in normal operation will cause the remote to transmit the POWER on/off commands for those devices selected during Master Power programming.
          To override this and transmit a POWER on/off command for a device not included in the Master Power selection, press the DEVICE key for that device and immediately press the POWER key.

        Channel Lock

          Channel Lock causes channel up and down functions to always operate the settop box independent of the device (TV, CBL, VCR, DVD or AUD) currently selected. The remote comes with Channel Lock activated. If you want the remote control to operate the channel function on your TV or VCR, you will need to deactivate Channel Lock:

          1. Press and hold the CBL device key until all the device keys begin to flash (approximately 3 seconds). Release the CBL key. The CBL key will
            continue to flash
          2. Press and release the CHANNEL ? key
          3. Press and release the CHANNEL ? key
          4. Press the OK key. The CBL device key will flash three times to confirm

          Repeat these steps to reactivate Channel Lock

        Button Descriptions

          Remote Controls for CA, OR and WA (297)

        ENT 6208


        View printable manual

        • ENT 6208

        Remote Controls for CA, OR and WA (298)

        Expand All | CollapseAll


        Automatic Programming

          The SmartScan™ programming instructions can also be found on the battery cover of the remote control. SmartScan™ will allow you to easily try all the available programming codes for the selected device and find the best match. If you prefer manual programming or already have the device codes see the Manual Programming section below

          1. Turn on the device
          2. Pressing and hold the desired device key (AUX, AUD, VCR, CBL, DVD, TV) until all device keys on the remote begin to flash
            (approximately 3 seconds), then release the key
          3. If the device you’re are attempting to program matches the selected device key (e.g. TV = TV key) proceed to step 5.
          4. If the device you’re are attempting to program does not match the selected key (e.g. a second VCR = AUX key), locate the correct prefix code for the device you wish to program (listed below). Press and release the number key that matches the prefix code
            Prefix: Device:
            0 Television
            1 DVD Player, VCR, or PVR
            4 Audio Devices
            5 Combo Units

          5. Press and release the POWER key. The device key will stop flashing and remain on
          6. Point the remote control at the selected device
          7. Press and hold the ? key until the device turns off. While holding the ? key the remote will send a new code approximately once every second. The device button will blink each time a new code is sent. If you pass the code that turns off the device, press the ? key to return to the previous code
          8. When the device turns off, you have found a candidate code. Press the POWER Key to turn device back on. Test various functions using the remote control to determine if this code will work. If primary functions do not work, make sure the device is still on then resume SmartScan™ by pressing the ? key to find another device code
          9. Once you have found a satisfactory code, press OK to lock the code. The power of the device must be on. The device key will then flash three times. Go to section 10 to recall and record your device codes. When all the codes have been attempted the device button will flash rapidly

        Manual Programming

          To manually set up the Enterprise to operate a device, find the manufacturer of the device in the list of manufacturers’ codes

          1. Press and hold the device key to be programmed until all device keys begin to flash (approximately 3 seconds). Release the key. The selected device key will continue to flash
          2. Enter the four digit code for the desired device using the number keys. After pressing the first digit, the device key should light and remain on if the programming is successful. After the last digit is pressed the device key should flash three times and turn off

            Audio Device -- >

            TV/DVD & TV/VCR Combos -- >

            TV -- >

            VCR/DVD/PVR -- >

          3. Test the code by trying various functions. If the primary function keys fail to respond satisfactorily try the next code listed for the manufacturer.

            If you have tried all the codes listed for the manufacturer and the device does not respond, try to program the device using Automatic Programming above

        Recalling aDevice Code

          Use the following steps to read the code set for a device. This is useful for determining a device code that was set using Automatic Programming above

          1. Press and hold the device key to be read until all device keys begin to flash (approximately 3 seconds). Release the key. The selected device key will continue to flash
          2. Press and release the OK key. The device key flashes each of the four digits in the code. A pause separates each digit. For example, three flashes represent the number 3, and a rapid flicker represents 0. A code of 1032 will be shown as:

            FLASH <pause> FLICKER <pause> FLASH, FLASH, FLASH <pause> FLASH, FLASH

            Count and record the sequence of flashes to determine the four-digit code.

        ProgrammingVolume Control

          By default, your Enterprise remote controls cable volume through the Cable Box, and the VCR and DVD through the Television. To allow volume control through a different device:

          1. Press and hold the CBL device key until all the device keys begin to flash. Release the CBL key. The CBL key will continue to flash
          2. Press and release the VOLUME ? key, the CBL key will remain on
          3. Press and release the VOLUME ? key. The CBL key will turn off when VOLUME ? is pressed, and will turn on when released
          4. Press and release the key corresponding to the device you wish to use to control volume (TV or AUD). After you release the key, the CBL key will flash three times and turn off

          To return volume control to the default state:

          1. Press and hold the CBL device key until all the device keys begin to flash. Release the CBL key. The CBL key will continue to flash
          2. Press and release the VOLUME ? key. The CBL device key will stop flashing and stay on
          3. Press and release the VOLUME ? key, and then press and release the OK key
          4. After you release the OK key, the CBL device key will flash three times and turn off

        Master PowerControl

          The Master Power function allows you to turn off and on two or more devices simultaneously with a single press of the POWER button. The following steps describe how to program the Master Power Control function:

          1. Press and hold the CBL device key until all the device keys begin to flash. Release the CBL key. The CBL key will continue to flash
          2. Press and release the POWER key
          3. Individually press and release each device key corresponding to the components you wish to be controlled by Master Power (starting with the cable device key).

            NOTE: If no keys are pressed in this step, no change will occur


          4. Press and release the POWER key. The CBL key will flash three times and turn off
          5. Manually turn on all devices. Then test the Master Power control by pressing the POWER key

          To disable Master Power, repeat the previous steps selecting only one device for Master Power (any device can be selected). The remote will now control the power ON/OFF of each device separately.

          NOTE: Once Master Power has been programmed for two or more devices, pressing the POWER key in normal operation will cause the remote to transmit the POWER on/off commands for those devices selected during Master Power programming.
          To override this and transmit a POWER on/off command for a device not included in the Master Power selection, press the DEVICE key for that device and immediately press the POWER key.

        Channel Lock

          Channel Lock causes channel up and down functions to always operate the settop box independent of the device (TV, CBL, VCR, DVD or AUD) currently selected. The remote comes with Channel Lock activated. If you want the remote control to operate the channel function on your TV or VCR, you will need to deactivate Channel Lock:

          1. Press and hold the CBL device key until all the device keys begin to flash (approximately 3 seconds). Release the CBL key. The CBL key will
            continue to flash
          2. Press and release the CHANNEL ? key
          3. Press and release the CHANNEL ? key
          4. Press the OK key. The CBL device key will flash three times to confirm

          Repeat these steps to reactivate Channel Lock

        Button Descriptions

          Remote Controls for CA, OR and WA (299)

        AllTouch (AT8550)


        View printable manual

        • AllTouch (AT8550)

        Remote Controls for CA, OR and WA (300)

        Expand All | CollapseAll


        What Devices Can I Control?

          Each mode key is associated with different groups of devices. You can use each mode key to control one of its associated devices:

          • CBL ... cable boxes, HDTV tuners, and satellite devices
          • TV ... TVs and HDTVs
          • VCR ... VCRs, digital video recorders (DVRs), DVD players, and CD players
          • DVD ... DVD players, CD players, VCRs, and DVRs
          • AUX ... receivers, tuners, and Home Theatre

        ProgrammingDevices to the Remote

          1. Turn on the device
          2. Press and hold SELECT and the appropriate mode key (CBL, TV, VCR, DVD, AUX) until all of the mode keys blink twice.
          3. Enter in the code for the device:

            CBL Group --- Cable Box ??

            TV Group --- TV ??

            TV Group --- HDTV ??

            VCR Group --- VCR ??

            VCR Group --- DVR ??

            DVD Group --- DVD player ??

            DVD Group --- CD player ??

            AUX Group --- Receiver/Tuner ??

            AUX Group --- Home Theatre ??

            The mode keys should then blink twice if the code was accepted

          4. Point the remote at the device, and press POWER, PLAY, CH? or CH? to test the device. If the device responds, you are done.

          5. If the device does not respond, repeat steps 2-4 for other codes (if applicable)
            • Still not successful? Try Searching for the Code (below)

        Searching for the code

          1. Turn on the device
          2. Press and hold SELECT and the appropriate mode key (CBL, TV, VCR, DVD, or AUX) until the mode keys blink twice
          3. Press 9, 9, 1. The mode key you selected in step 2 blinks twice
          4. Point the remote toward the device, and press PLAY . The remote automatically tests each code in its library, beginning with the most common codes. The mode key blinks once each time the remote transmits a new code*. The mode key blinks twice when it reaches the last code

            *Depending the the mode key, the remote will check through a certain amount of codes:

            • CBL mode: 23
            • TV mode: 225
            • DVD mode: 206
            • VCR mode: 210
            • AUX mode: 38
          5. As soon as the device powers off, press SELECT
          6. Verify the new code is correct by pressing POWER
          7. If the device powers on again, press SELECT to assign the code. If not complete the following steps:
            1. Turn the device on
            2. Press CH? or CH? to step forward or back to the correct code
            3. When the device turns off, press SELECT to assign the code

        Find Your Code

          Find out which code programmed the mode key to control your device

          1. Press and hold SELECT and the appropriate mode key (CBL, TV, VCR, DVD, or AUX) until all mode keys blink twice
          2. Press 9, 9, 0. The mode key you selected in step 1 blinks twice
          3. Press 1 and then count the number of times the mode key blinks. The number of blinks indicates the first digit in the code
            • For example, 4 blinks indicates the first digit in the code is 4. If the mode key does not blink, the digit is 0.
          4. Press 2 and then count the number of times the mode key blinks. This number indicates the second number in the code
          5. Press 3 and then count the number of times the mode key blinks. This number indicates the third number in the code
          6. Press 4 and then count the number of times the mode key blinks. This number indicates the fourth number in the code
          7. After all four numbers in the code are identified, all mode keys blink three times

        Controlling POWER key for Multiple Devices at Once

          The Remote's POWER key can turn on/off multiple devices at once, rather than needing to change.

          1. Press and hold the SELECT and CBL keys until the mode keys blink twice
          2. Using the remote keypad, press 9, 9, 8. The CBL key blinks twice
          3. Press the mode key (CBL, TV, VCR, DVD, or AUX) for the first device in the group of devices you want to power on and off at once. The CBL key blinks twice
          4. Press the mode key for the second device in the group of devices you want to power on and off at once. The CBL key blinks twice
          5. Repeat step for additional devices
          6. When done, press SELECT to save your power settings. All mode keys blink three times

          To change the POWER key back to it's default

          1. Press and hold SELECT and CBL until all mode keys blink twice
          2. Press 9, 9, 8. The CBL key blinks twice
          3. Press SELECT to save your power settings. All mode keys blink three times
          4. The POWER key will only control the device/mode the remote is in

        Channel Control Lock

          You can lock the remote control to change channels only through the cable box, whether in CBL, VCR, DVD, or TV mode.

          1. Press and hold SELECT and CBL until all mode keys blink twice.
          2. Press 9, 9, 7. The CBL key blinks twice.
          3. Press the CBL. All mode keys blink three times.

            NOTE: In AUX mode, the remote always controls channels for the AUX device

          Controlling Channels on Different Devices

          1. Press and hold SELECT and CBL until all mode keys blink twice.
          2. Press 9, 9, 7. The CBL key blinks twice.
          3. Press SELECT. All mode keys blink three times
          4. The channel keys will work with the mode key you select

        Volume Control

          You can lock the remote control to control volume and mute through one specific device, whether in CBL, VCR, DVD, or TV mode

          To Control volume and mute through the TV only:

            1. Press and hold the SELECT and CBL keys until the mode keys blink twice
            2. Press 9, 9, 3. The CBL key blinks twice
            3. Press TV. All mode keys blink three times

              NOTE: In AUX mode, the remote always controls volume and mute for the AUX device

          To Control volume and mute through the Cable Box only:

            1. Press and hold the SELECT and CBL keys until the mode keys blink twice
            2. Press 9, 9, 3. The CBL key blinks twice
            3. Press CBL. All mode keys blink three times

              NOTE: In AUX mode, the remote always controls volume and mute for the AUX device

          To Control volume and mute through whatever mode the remote is in:

            1. Press and hold the SELECT and CBL keys until the mode keys blink twice
            2. Press 9, 9, 3. The CBL key blinks twice
            3. Press SELECT. All mode keys blink three times

        AT8400


        View printable manual

        • AT8400

        Remote Controls for CA, OR and WA (301)

        Expand All | CollapseAll


        Programming Devices into the AT8400 Remote

          Note: These instructions assume you have already selected the proper device code(s).

          1. Turn on the device
          2. Press and hold SELECT plus the appropriate device key until all mode keys blink twice
          3. Enter in the code for the device:

            TV -- >

            VCR -- >

            CBL -- >

            AUX (Receiver) -- >

            AUX (Amplifier) -- >

            The mode keys should then blink twice if the code was accepted

          4. Test the device by pressing POWER. If the device responds, the program was successful
          5. If the device does not respond, repeat steps 2-4 for other codes (if applicable)

        Programming Volume Control:

          Note: The default device is TV. For controlling the volume through the cable box, press the Settings button twice to go into the "General Settings" menu and make sure thatthe "Audio: Volume Control" setting is set to "Variable".

          1. Turn on the device
          2. Press and hold the SELECT and CBL keys until the mode keys blink twice
          3. Using the remote keypad, press 9, 9, 3. The mode keys will blink twice
          4. Press the mode key for the device you want to control the volume
          5. Point the remote at the device and verify the volume is being adjusted through it

        ProgrammingCable Receiver

          1. Press and hold the SELECT and CBL keys until the mode keys blink twice
          2. Using the remote keypad, press 9, 9, 6. The mode keys will blink twice
          3. Press CH - to unlock the remote
          4. Enter in the 4 digits to program the CBL key

        Searching forCodes

          1. Turn on the device
          2. Press and hold SELECT and the appropriate mode key until the mode keys blink twice
          3. Using the remote keypad, press 9, 9, 1. The mode keys will blink twice
          4. Point the remote at the device and press PLAY. The remote will now automatically test each code in its library beginning with the most common codes. The mode key will flash twice when it reaches the end of the codes stored in its library
          5. As soon as the device powers down, press the SELECT key
          6. Verify that the code is correct by pressing the POWER key
          7. If the device powers on again, press the SELECT key again to lock in the code
          8. If it does not, turn the device on and press CH + or CH - to step to the correct code. When the device turns off, press SELECT to lock in the code

        Identifying ProgrammedCodes

          1. Press and hold the SELECT and CBL keys until the mode keys blink twice
          2. Using the remote keypad, press 9, 9, 0. The mode keys will blink twice
          3. Press 1 then count the number of times the mode key blinks. This will be the first digit in the code. If the key does not blink the digit is 0
          4. Repeat Step 3 substituting 2, 3 and 4 to obtain the other 4 code digits
          5. Write down the code for future reference

        UR3L-SR4


        View printable manual

        • UR3L-SR4

        Remote Controls for CA, OR and WA (302)

        Expand All | CollapseAll


        Quick Set Up Method

          1. Turn on the device you want to program. To program your TV, turn on the TV
          2. Press and hold the [Device] key for 5 seconds until the Device LED will blink once and stays on. Continue to hold the [Device] key and press the number key assigned to your brand in the Quick Setup Code Table and release both [Device] key and the number key to save the code
            CBL TV DVD
            0 PACE DTA
            1 SA/CISCO, SAMSUNG, PACE DIGITAL
            2 MOTOROLA DIGITAL
            3 MOTOROLA DTA
            4 EVOLUTION DTA
            5 CISCO IPTV
            6 ADB IPTV
            7 TECHNICOLOR
            8 AMINO 140/540 IPTV
            9 MOTOROLA IPTV
            0 SANYO
            1 SONY
            2 SAMSUNG
            3 LG
            4 TOSHIBA
            5 PANASONIC
            6 PHILIPS
            7 HITACHI
            8 SHARP
            9 VIZIO
            0 HITACHI
            1 SONY
            2 PHILIPS
            3 SAMSUNG
            4 PHILIPS MAGNAVOX
            5 PANASONIC
            6 LG
            7 JVC
            8 DENON
            9 PIONEER
            The Device LED will blink twice to confirm that the code is stored
          3. Point the remote control at the device
          4. Press the power button. If it turns off, it is programmed for your component. If it does not turn off, use the Pre-Programmed 3-Digit code Method or Scanning Method. Repeat the steps above for all devices (CBL, TV, DVD)

        Manual Programming

          The remote control can be programmed by entering a three-digit code number that corresponds to particular brands and models of equipment

          1. Turn on the equipment that you want the remote control to operate (Cable Box, TV or DVD)
          2. Press the [Device] button and the [OK/SEL] button simultaneously for three seconds. The corresponding device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 30 seconds. The next step must be entered while the LED is on
          3. Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. If there are more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off
            Cable Converter- [CBL] ?
            Cable IPTV - [CBL] ?
            TV - [TV] ?
            DVD - [DVD] ?
            PVR/DVR (TiVo)>- [DVD] ?

            • You can verify that you have selected the correct code by pressing [POWER]. The equipment should turn back on. Then try all of the functions on the remote control (i.e. volume, mute, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, repeat the instructions from step 3 using the next three digit code number from the brand list
          4. Store the three-digit code by pressing the same [Device] button once again. The device LED will blink twice to confirm that the code has been stored.

        Auto Search Method

          If none of the three digit code numbers assigned to your brand of equipment works, or the code table does not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by following steps:

          1. Turn on the equipment that you want the remote control to operate (Cable Box, TV or DVD)
          2. Press the [Device] button and [OK/SEL] simultaneously for three seconds

            The device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 30 seconds. The next step must be entered while the LED is on

          3. Press [CH?] or [CH?] one at a time or keep it pressed. The remote will emit a series of Power ON/OFF code signals. Release [CH?] or [CH?] as soon as the equipment turns off

            You can verify that you have selected the correct code by pressing [POWER]. The equipment should turn back on. Then try all of the functions on the remote control (i.e. volume, mute, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, repeat the instructions from STEP 3 to continue the Auto Search Method

          4. Press the same [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored.

        Code Number Readback

          This is useful for determining a device code that was set using the Auto Search Method above

          1. Press the [Device] button and [SELECT] simultaneously for 3 seconds
          2. The device LED will light on for 20 seconds. The next step must be entered while LED is on
          3. Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code number
            • Each digit is separated by 1 second. Ten blinks is equal to the number 0
            • For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks

        Programming aSecond TV to DVD key

          1. Press [DVD] and [SELECT] simultaneously for 3 seconds.
            • The device LED will light on for 30 seconds. The next step must be entered while LED is on
          2. Press [TV]
          3. Point the remote control toward the equipment and enter the three-digit code number assigned to your TV brand from the code tables. The equipment will turn off when the correct three-digit code number has been entered.
            TV -- >
          4. Press [DVD] once again. The device LED will blink twice to confirm that the code has been stored

        The Learning Method

          1. Press the [Device] button (CBL, TV or DVD) to be programmed and the [INPUT] buttons simultaneously for 3 seconds until the Device LED light turns on
          2. Line up the UR3L-SR4 to the other remote, head-to-head, 1 or 2 inches apart
          3. Press any button on the UR3LSR4 that you want to teach a command to. For example, if you want to teach the [MUTE] button, press the [MUTE] button
          4. Press and hold the [MUTE] button on the other remote until the UR3L-SR4 Device LED light blinks twice The LED will blink 5 times if there was an error in the learning process. In so, repeat STEPS 3 and 4. Continue learning other buttons by repeating STEPS 3 and 4
          5. Once you have completed teaching UR3L-SR4 all desired commands for that Device, save the learned commands by pressing the [Device] and [INPUT] buttons simultaneously until the Device LED blinks 3 times. Now test all the buttons to make sure they learned correctly

          Erasing a Single Learned Command

          1. Press the [Device] and [INPUT] buttons simultaneously for 3 seconds until the Device LED light turns on
          2. Press and hold the button you want to erase for 3 seconds. The Device LED will blink twice to confirm the erasure
          3. To exit, press and hold both the [Device] and [INPUT] buttons simultaneously until the Device LED blinks 3 times

          Erasing All Learned Commands from One Device

          1. Press the [Device] and [INPUT] buttons simultaneously for 3 seconds until the Device LED light turns on
          2. Press and hold both the [Device] button you want to erase and the [PAUSE] button for 5 seconds. The Device LED will blink twice to confirm the erasure
          3. To exit, press and hold both the [Device] and [INPUT] buttons simultaneously until the Device LED blinks 3 times

        Programming the'All Off' Button

          This allows you to program the [All OFF] button so it can send up to three power On/Off commands with one button press

          1. Press [CBL]
          2. Press [All OFF] and [SELECT] simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds
          3. Press the first [Device] button you want to store and then the [POWER] button
          4. Press the second [Device] button you want to store and then the [POWER] button
          5. Press the third [Device] button you want to store and then the [POWER] button
          6. Press [CH?] to save the power commands you stored. The [CBL] button will blink twice to confirm

        Volume Control

          Volume and Mute control are factory programmed to the respective Device mode you select, as follows:

          CBL : TV TV : TV DVD : TV
          If you wish to store the Cable volume control in CBL mode, use the following steps

          1. Press the [OK/SEL] button and [CBL] button simultaneously for three seconds.

            The device LED will turn on for 30 seconds. The next step must be performed while the LED is on

          2. Press the [VOL?] button. The device LED will blink
          3. Press [CBL] button. The device LED will blink twice to confirm the programming

          To restore the volume control back to your TV in CBL mode, repeat the above steps by replacing [CBL] with [TV] in Step 3.

        Programming Channel Control

          Channel controls are factory-programmed to automatically transfer to the respective Device mode you select, as follows:

          CBL : CBL TV : CBL DVD : DVD
          If you wish to store the TV channel controls in TV mode, use the following steps.

          1. Press the [OK/SEL] button and [TV] button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while the LED is on
          2. Press the [VOL? ] button. The device LED will blink
          3. Press [TV] button. The device LED will blink twice to confirm the programming

          To return TV device to CBL channel repeat steps above replacing [TV] with [CBL] in Step 3

        Low Battery Warning

          When the battery is low, the remote control LED blinks 2 times whenever a [Device] button is pressed to turn on equipment.

        Memory Lock

          This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.

        Button Descriptions

          Remote Controls for CA, OR and WA (303)

        CLIKR-5 (UR5U-8500L)


        View printable manual

        • CLIKR-5 (UR5U-8500L)

        Remote Controls for CA, OR and WA (304)

        Expand All | CollapseAll

        Three-Digit Code Programming Method

          1. Turn on the device you want to program (TV, DVD or AUX)
          2. Press the [DEVICE] button (TV, DVD or AUX) to be programmed and [OK/SEL] button simultaneously for 3 seconds. The device LED will light for 30 seconds indicating the unit is ready to be programmed
          3. Point the remote control toward the device and enter the 3-digit code number assigned to your brand
            TV ?
            VCR (use VCR key) ?
            TV/VCR (use VCR key) ?
            DVD (use DVD key) ?
            TV/DVD Combos (use DVD key) ?
            TV/DVD/VCR Combos (use DVD key) ?
            DVD/VCR Combos (use DVD key) ?
            DVD Recorders (use DVD key) ?
            Audio Device (use AUX key) ?
            TiVo (use AUX key) ?
            • If the 3-digit code number you just entered is correct, the device will turn Off
            • If it did not turn Off, continue entering code numbers listed for that brand until the device turns Off
          4. After you’ve entered the correct code number and the device has turned Off, press the [POWER] button to turn the device back On. Now it’s time to test the VOLUME and MUTE buttons for the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all work
          5. If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand
          6. Once you have found the correct 3-digit code, save it by pressing the same [DEVICE] button one more time. The [DEVICE] LED light will blink twice to confirm that the code was successfully stored

        Auto Search Method

          If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:

          1. Turn on the equipment you wish to operate
          2. Pressthe [DEVICE] button and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
            • The device LED will light on for 30 seconds. The next step must be entered while LED is on
          3. Press the [CH?] or [CH?] button one step at a time or keep it pressed. The remote will emit a series of Power ON/OFF commands. Release the [CH?] or [CH?] button as soon as the equipment turns off.
          4. Verify that you selected the correct code by pressing [POWER] again. The equipment should either turn on or turn off
          5. Press the [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored

        Code NumberReadback

          1. Press the [DEVICE] button and [OK/SEL] simultaneously for 3 seconds

            The device LED will light on for 30 seconds. The next step must be entered while LED is on

          2. Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code number
            • Each digit is separated by 1 second. Ten blinks is equal to the number 0
            • For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks

        Programming a5th Device toAUX Button

          You can take advantage of the AUX function to program a 4th Component such as a second TV, VCR, DVD or Audio Component

          1. Turn on the equipment you wish to operate.
          2. Press [AUX] and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
            • The device LED will light on for 20 seconds. The next step must be entered while LED is on
          3. Press the desired [DEVICE] button. Point the remote control toward the device and enter the 3-digit code number assigned to your brand
            TV ?
            VCR (use VCR key) ?
            TV/VCR (use VCR key) ?
            DVD (use DVD key) ?
            TV/DVD Combos (use DVD key) ?
            TV/DVD/VCR Combos (use DVD key) ?
            DVD/VCR Combos (use DVD key) ?
            DVD Recorders (use DVD key) ?
            Audio Device (use AUX key) ?
            TiVo (use AUX key) ?
          4. If the 3-digit code number you just entered is the correct number, the device will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the device turns Off
          5. Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, you need to find a new code
          6. Press [AUX] one more time. The desired [DEVICE] LED light will blink twice to confirm the code was stored

        Programming the System On/Off Button

          The System on/off button can send out up to five power on/off commands for the devices you programmed into the remote control

          1. Press [CBL]
          2. Press [System On/Off] and [OK/SEL] simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds
          3. Press [TV]
          4. Press [DVD] (if adding)
          5. Press [VCR] (if adding)
          6. Press [AUX] (if adding)
          7. Press [CH?] to save the power commands you stored. The [CBL] button will blink twice to confirm

        Programming Channel Controls

          Channel controls (CH?, CH?, LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:

          CBL : CBL TV : CBL VCR : CBL DVD : DVD AUX : AUX
          If you wish to store the TV channel controls in TV mode, use the following steps

          1. Press [TV] and [OK/SEL] button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while the LED is on
          2. Press the [VOL?] button. The device LED will blink
          3. Press [TV] button. The device LED will blink twice to confirm the programming

            To return TV device to CBL channel repeat steps above replacing [TV] with [CBL] in Step 3

        Volume Control

          Volume and Mute control are factory programmed to the respective Device mode you select, as follows:

          CBL : TV TV : TV DVD : TV AUX : AUX
          If you wish to store the Cable volume control in CBL mode, use the following steps

          1. Press [CBL] and [OK/SEL] simultaneously for three seconds
            • [CBL] will turn on for 20 seconds. The next step must be performed while the LED is on
          2. Press the [VOL?] button. The device LED will blink
          3. Press [CBL] button. The device LED will blink twice to confirm the programming

          To restore the volume control back to your TV in CBL mode, repeat the above steps by replacing [CBL] with [TV] in Step 3

        Macro key(s)

          In the CBL mode, the M1, M2, and Help buttons can be programmed to act as a macro or favorite channel button. You can send out up to ten commands with one button press

          1. Press the [CBL] button to select the CBL mode
          2. Press the [Macro] button and [OK/SEL] button simultaneously for 3 seconds. The [CBL] device LED will turn on for 20 seconds
          3. Press up to 10 buttons you wish to store. The [CBL] device LED will blink once for each command entered
          4. Press the [CH?] button to store the functions that were selected. The [CBL] device LED will blink twice to confirm the storage of functions

        Low Battery Warning

          When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.

        Memory Lock

          This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.

        Button Functions

          Remote Controls for CA, OR and WA (305)

        CLIKR-5 (UR5U-8500)


        View printable manual

        • CLIKR-5 (UR5U-8500)

        Remote Controls for CA, OR and WA (306)

        Expand All | CollapseAll

        Three-Digit Code Programming Method

          1. Turn on the device you want to program (TV, DVD or AUX)
          2. Press the [Device] button (TV, DVD or AUX) to be programmed and [OK/SEL] button simultaneously for 3 seconds. The device LED will light for 30 seconds indicating the unit is ready to be programmed
          3. Point the remote control toward the device and enter the 3-digit code number assigned to your brand
            TV ?
            VCR (use VCR key) ?
            TV/VCR (use VCR key) ?
            DVD (use DVD key) ?
            TV/DVD Combos (use DVD key) ?
            TV/DVD/VCR Combos (use DVD key) ?
            DVD/VCR Combos (use DVD key) ?
            DVD Recorders (use DVD key) ?
            Audio Device (use AUX key) ?
            TiVo (use AUX key) ?
            • If the 3-digit code number you just entered is correct, the device will turn Off
            • If it did not turn Off, continue entering code numbers listed for that brand until the device turns Off
          4. After you’ve entered the correct code number and the device has turned Off, press the [POWER] button to turn the device back On. Now it’s time to test the VOLUME and MUTE buttons for the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all work
          5. If any of the functions do not work as they should, repeat from step 3 using the next 3-digit code number listed for that brand
          6. Once you have found the correct 3-digit code, save it by pressing the same [DEVICE] button one more time. The [Device] LED light will blink twice to confirm that the code was successfully stored

        Auto Search Method

          If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:

          1. Turn on the equipment you wish to operate
          2. Pressthe [Device] button and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
            • The device LED will light on for 30 seconds. The next step must be entered while LED is on
          3. Press the [CH?] or [CH?] button one step at a time or keep it pressed. The remote will emit a series of Power ON/OFF commands. Release the [CH?] or [CH?] button as soon as the equipment turns off.
          4. Verify that you selected the correct code by pressing [POWER] again. The equipment should either turn on or turn off
          5. Press the [Device] button to store the code. The Device LED will blink twice to confirm that the code has been stored

        Code NumberReadback

          1. Press the [Device] button and [OK/SEL] simultaneously for 3 seconds

            The device LED will light on for 30 seconds. The next step must be entered while LED is on

          2. Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code number
            • Each digit is separated by 1 second. Ten blinks is equal to the number 0
            • For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks

        Programming a5th Device toAUX Button

          You can take advantage of the AUX function to program a 4th Component such as a second TV, VCR, DVD or Audio Component

          1. Turn on the equipment you wish to operate.
          2. Press [AUX] and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
            • The device LED will light on for 20 seconds. The next step must be entered while LED is on
          3. Press the desired [Device] button. Point the remote control toward the device and enter the 3-digit code number assigned to your brand
            TV ?
            VCR (use VCR key) ?
            TV/VCR (use VCR key) ?
            DVD (use DVD key) ?
            TV/DVD Combos (use DVD key) ?
            TV/DVD/VCR Combos (use DVD key) ?
            DVD/VCR Combos (use DVD key) ?
            DVD Recorders (use DVD key) ?
            Audio Device (use AUX key) ?
            TiVo (use AUX key) ?
          4. If the 3-digit code number you just entered is the correct number, the device will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the device turns Off
          5. Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, you need to find a new code
          6. Press [AUX] one more time. The desired [Device] LED light will blink twice to confirm the code was stored

        Programming the System On/Off Button

          The System on/off button can send out up to five power on/off commands for the devices you programmed into the remote control

          1. Press [CBL]
          2. Press [System On/Off] and [OK/SEL] simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds
          3. Press [TV]
          4. Press [DVD] (if adding)
          5. Press [VCR] (if adding)
          6. Press [AUX] (if adding)
          7. Press [CH?] to save the power commands you stored. The [CBL] button will blink twice to confirm

        Programming Channel Controls

          Channel controls (CH?, CH?, LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:

          CBL : CBL TV : CBL VCR : CBL DVD : DVD AUX : AUX
          If you wish to store the TV channel controls in TV mode, use the following steps

          1. Press [TV] and [OK/SEL] button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while the LED is on
          2. Press the [VOL?] button. The device LED will blink
          3. Press [TV] button. The device LED will blink twice to confirm the programming

            To return TV device to CBL channel repeat steps above replacing [TV] with [CBL] in Step 3

        Volume Control

          Volume and Mute control are factory programmed to the respective Device mode you select, as follows:

          CBL : TV TV : TV DVD : TV AUX : AUX
          If you wish to store the Cable volume control in CBL mode, use the following steps

          1. Press [CBL] and [OK/SEL] simultaneously for three seconds
            • [CBL] will turn on for 20 seconds. The next step must be performed while the LED is on
          2. Press the [VOL?] button. The device LED will blink
          3. Press [CBL] button. The device LED will blink twice to confirm the programming

          To restore the volume control back to your TV in CBL mode, repeat the above steps by replacing [CBL] with [TV] in Step 3

        Macro key(s)

          In the CBL mode, the M1, M2, Help, BLANK buttons can be programmed to act as a macro or favorite channel button. You can send out up to ten commands with one button press

          1. Press the [CBL] button to select the CBL mode
          2. Press the [Macro] button and [OK/SEL] button simultaneously for 3 seconds. The [CBL] device LED will turn on for 20 seconds
          3. Press up to 10 buttons you wish to store. The [CBL] device LED will blink once for each command entered
          4. Press the [CH?] button to store the functions that were selected. The [CBL] device LED will blink twice to confirm the storage of functions

        Low Battery Warning

          When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.

        Memory Lock

          This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.

        Button Functions

          Remote Controls for CA, OR and WA (307)

        CLIKR-5 (UR5U-8700L/8720L)


        View printable manual

        • CLIKR-5 (UR5U-8700L/8720L)

        Remote Controls for CA, OR and WA (308)

        Expand All | CollapseAll

        Three-Digit Code Programming Method

          1. Turn on the device you want to program (TV, DVD, VCR or AUX)
          2. Press the [Device] button (TV, DVD, VCR or AUX) to be programmed and [OK/SEL] button simultaneously for 3 seconds. The device LED will light for 30 seconds indicating the unit is ready to be programmed
          3. Point the remote control toward the device and enter the 3-digit code number assigned to your brand

            TV -- >

            VCR (use VCR key) -- >

            TV/VCR Combos (use VCR key) -- >

            DVD (use DVD key) -- >

            DVD Recorders (use DVD key) -- >

            TV/DVD Combos (use DVD key) -- >

            TV/DVD/VCR Combos (use DVD key) -- >

            DVD/VCR Combos (use DVD key) -- >

            Audio Device (use AUX key) -- >

            TiVo (use AUX key) -- >

            • If the 3-digit code number you just entered is correct, the device will turn Off
            • If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off
          4. After you’ve entered the correct code number and the device has turned Off, press the [POWER] button to turn the device back On. Now it’s time to test the VOLUME and MUTE buttons for the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all work
          5. If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand
          6. Once you have found the correct 3-digit code, save it by pressing the same [Device] button one more time
          7. The [Device] LED light will blink twice to confirm that the code was successfully stored

        Auto Search Method

          If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:

          1. Turn on the equipment you wish to operate
          2. Pressthe [Device] button and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
            • The device LED will light on for 30 seconds. The next step must be entered while LED is on
          3. Press the [CH?] or [CH?] button one step at a time or keep it pressed. The remote will emit a series of Power ON/OFF commands. Release the [CH?] or [CH?] button as soon as the equipment turns off.
          4. Verify that you selected the correct code by pressing [POWER] again. The equipment should either turn on or turn off
          5. Press the [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored

        Code NumberReadback

          1. Press the [Device] button and [OK/SEL] simultaneously for 3 seconds
          2. The device LED will light on for 30 seconds. The next step must be entered while LED is on
          3. Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code number
            • Each digit is separated by 1 second. Ten blinks is equal to the number 0
            • For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks

        The Learning Method

          1. Press the [Device] button (AUX, TV, VCR or DVD) to be programmed and the [ASPECT] buttons simultaneously for 3 seconds until the Device LED light turns on
          2. Line up the CLIKR-5 to the other remote, head-to-head, 1 or 2 inches apart
          3. Press any button on the CLIKR-5 that you want to teach a command to. For example, if you want to teach the [MUTE] button, press the [MUTE] button
          4. Press and hold the [MUTE] button on the other remote until the CLIKR-5 Device LED light blinks twice

            The LED will blink 5 times if there was an error in the learning process. In so, repeat STEPS 3 and 4. Continue learning other buttons by repeating STEPS 3 and 4

          5. Once you have completed teaching CLIKR-5 all desired commands for that Device, save the learned commands by pressing the [Device] and [ASPECT] buttons simultaneously until the Device LED blinks 3 times. Now test all the buttons to make sure they learned correctly

          Erasing a Single Learned Command

          1. Press the [Device] and [ASPECT] buttons simultaneously for 3 seconds until the Device LED light turns on
          2. Press and hold the button you want to erase for 3 seconds. The Device LED will blink twice to confirm the erasure
          3. To exit, press and hold both the [Device] and [ASPECT] buttons simultaneously until the Device LED blinks 3 times

          Erasing All Learned Commands from One Device

          1. Press the [Device] and [ASPECT] buttons simultaneously for 3 seconds until the Device LED light turns on
          2. Press and hold both the [Device] button you want to erase and the [PAUSE] button for 5 seconds. The Device LED will blink twice to confirm the erasure
          3. To exit, press and hold both the [Device] and [ASPECT] buttons simultaneously until the Device LED blinks 3 times

        Programming a5th Device toAUX Button

          You can take advantage of the AUX function to program a 4th Component such as a second TV, VCR, DVD or Audio Component

          1. Turn on the equipment you wish to operate
          2. Press [AUX] and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
            • The device LED will light on for 30 seconds. The next step must be entered while LED is on
          3. Press the [Device] button you want to setup. Point the remote control toward the Device and enter the 3-digit code number assigned to your brand

            TV -- >

            VCR (use VCR key) -- >

            TV/VCR Combos (use VCR key) -- >

            DVD (use DVD key) -- >

            DVD Recorders (use DVD key) -- >

            TV/DVD Combos (use DVD key) -- >

            TV/DVD/VCR Combos (use DVD key) -- >

            DVD/VCR Combos (use DVD key) -- >

            Audio Device (use AUX key) -- >

            TiVo (use AUX key) -- >

          4. If the 3-digit code number you just entered is the correct number, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off
          5. Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, you need to find a new code.
          6. Press [AUX] one more time. The Component LED light will blink twice to confirm the code was stored

        Programming the System On/Off Button

          The System on/off button can send out up to three power on/off commands for the devices you programmed into the remote control

          1. Press [CBL]
          2. Press [System On/Off] and [OK/SEL] simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds
          3. Press [TV]
          4. Press [DVD] (if adding)
          5. Press [VCR] (if adding)
          6. Press [AUX] (if adding)
          7. Press [CH?] to save the power commands you stored. The [CBL] button will blink twice to confirm

        Programming Channel Controls

          Channel controls (CH?, CH?, LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:

          CBL : CBL TV : CBL VCR : CBL DVD : DVD AUX : AUX

          If you wish to store the TV channel controls in TV mode, use the following steps

          1. Press the [OK/SEL] button and [TV] button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while the LED is on
          2. Press the [VOL?] button. The device LED will blink
          3. Press [TV] button. The device LED will blink twice to confirm the programming

            To return TV device to CBL channel repeat steps above replacing [TV] with [CBL] in Step 3

        Volume Control

          Volume and Mute control are factory programmed to the respective Device mode you select, as follows:

          CBL : CBL TV : TV VCR : TV DVD : TV AUX : AUX

          If you wish to store the TV volume control in CBL mode, use the following steps

          1. Press [CBL] button and [OK/SEL] simultaneously for three seconds
            • The device LED will turn on for 30 seconds. The next step must be performed while the LED is on
          2. Press the [VOL?] button. The device LED will blink
          3. Press [TV] button. The device LED will blink twice to confirm the programming

          To restore the volume control back to your TV in CBL mode, repeat the above steps by replacing [TV] with [CBL] in Step 3

        Macro (blank) Button

          In the CABLE device mode, the two [M], [M2] buttons (see button functions below) can be programmed to act as a 'Favorite Channel' button. This allows you to program up to five 2-digit channels, four 3-digit channels or three 4-digit channels that can be accessed with one button press

          1. Press the [CBL] button to select the CBL mode
          2. Press the [MACRO] button and [OK/SEL] button simultaneously for 3 seconds. The [CBL] button will turn on for 20 seconds
            • The [MACRO] button will turn on for 30 seconds. The next step must be performed while the LED is on
          3. Enter the the 2, 3 or 4-digit code for the channel you want programmed first (for example, 0-0-7) using the Number Pad, then press the [STOP] button. Then enter the code for the next channel (for example, 0-5-0), then press the [STOP] button. Repeat this process for the third channel. The [CBL] button will blink once for each channel entered
          4. Press the [CH?] button to store the commands that were selected. The [CBL] button will blink twice to confirm the storage of commands
          5. To access the programmed channels, press the [MACRO] button once. This will bring up the first channel. Press once again and it will bring up the second channel. Press again and it will bring up the third channel

          To erase the Macro programming and return to the original function:

          1. Press the [CBL] button to select the CABLE mode
          2. Press a [MACRO] button and the [OK/SEL] button simultaneously for 3 seconds
            • The CBL device LED will turn on for 30 seconds. The next step must be performed while the LED is on
          3. Press the [CH?] button to erase the functions stored in the button. The CBL button will blink twice to confirm that the memory button has been erased

        Low Battery Warning

          When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.

        Memory Lock

          This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.

        Button Functions

          Remote Controls for CA, OR and WA (309)

        UR5U-8400


        View printable manual

        • UR5U-8400

        Remote Controls for CA, OR and WA (310)

        Expand All | CollapseAll

        Three-Digit Code Programming Method

          1. Turn on the device you want to program (TV, DVD or AUX)
          2. Press the [Device] button (TV, DVD or AUX) to be programmed and [SELECT] button simultaneously for 3 seconds. The device LED will light for 20 seconds indicating the unit is ready to be programmed
          3. Point the remote control toward the device and enter the 3-digit code number assigned to your brand

            TV ?

            VCR & TV/VCR (use VCR key) ?

            DVD & TV/DVD (use DVD key) ?

            Audio Device (use AUX key) ?

            DMX & DCR (use AUX key) ?

            • If the 3-digit code number you just entered is correct, the device will turn Off
            • If it did not turn Off, continue entering code numbers listed for that brand until the device turns Off
          4. After you’ve entered the correct code number and the device has turned Off, press the [POWER] button to turn the device back On. Now it’s time to test the VOLUME and MUTE buttons for the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all work
          5. If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand
          6. Once you have found the correct 3-digit code, save it by pressing the same [DEVICE] button one more time. The [Device] LED light will blink twice to confirm that the code was successfully stored

        Auto Search Method

          If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:

          1. Turn on the equipment you wish to operate
          2. Pressthe [Device] button and [SELECT] simultaneously for 3 seconds. The device LED will turn on
            • The device LED will light on for 20 seconds. The next step must be entered while LED is on
          3. Press the [CH?] or [CH?] button one step at a time or keep it pressed. The remote will emit a series of Power ON/OFF commands. Release the [CH?] or [CH?] button as soon as the equipment turns off.
          4. Verify that you selected the correct code by pressing [POWER] again. The equipment should either turn on or turn off
          5. Press the [Device] button to store the code. The device LED will blink twice to confirm that the code has been stored

        Code NumberReadback

          1. Press the [Device] button and [SELECT] simultaneously for 3 seconds

            The device LED will light on for 30 seconds. The next step must be entered while LED is on

          2. Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code number
            • Each digit is separated by 1 second. Ten blinks is equal to the number 0
            • For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks

        Programming aSecond TV toAUX Button

          You can take advantage of the AUX function to program a 4th Component such as a second TV, VCR, DVD or Audio Component

          1. Turn on the equipment you wish to operate
          2. Press [AUX] and [SELECT] simultaneously for 3 seconds. The device LED will turn on
            • The device LED will light on for 20 seconds. The next step must be entered while LED is on
          3. Press [TV]. Point the remote control toward the Component and enter the 3-digit code number assigned to your brand

            TV ?

          4. If the 3-digit code number you just entered is the correct number, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off
          5. Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, you need to find a new code
          6. Press [AUX] one more time. The Device LED light will blink twice to confirm the code was stored

        Programming the System On/Off Button

          The System on/off button can send out up to five power on/off commands for the devices you programmed into the remote control

          1. Press [CBL]
          2. Press [System On/Off] and [SELECT] simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds
          3. Press [TV]
          4. Press [DVD] (if adding)
          5. Press [VCR] (if adding)
          6. Press [AUX] (if adding)
          7. Press [CH?] to save the power commands you stored. The [CBL] button will blink twice to confirm

        Programming Channel Controls

          Channel controls (CH?, CH?, LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:

          CBL : CBL TV : CBL VCR : CBL DVD : DVD AUX : AUX

          If you wish to store the TV channel controls in TV mode, use the following steps

          1. Press [TV] and [SELECT] button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while the LED is on
          2. Press the [VOL?] button. The device LED will blink
          3. Press [TV] button. The device LED will blink twice to confirm the programming

            To return TV device to CBL channel repeat steps above replacing [TV] with [CBL] in Step 3

        Volume Control

          Volume and Mute control are factory programmed to the respective Device mode you select, as follows:

          CBL : TV TV : TV DVD : TV AUX : AUX

          If you wish to store the Cable volume control in CBL mode, use the following steps

          1. Press [CBL] and [SELECT] simultaneously for three seconds
            • [CBL] will turn on for 20 seconds. The next step must be performed while the LED is on
          2. Press the [VOL?] button. The device LED will blink
          3. Press [CBL] button. The device LED will blink twice to confirm the programming

          To restore the volume control back to your TV in CBL mode, repeat the above steps by replacing [CBL] with [TV] in Step 3

        Programming For Advanced Function (blank key)

          In the CBL mode, the BLANK button can be programmed to act as a macro or favorite channel button. You can send out up to ten commands with one button press

          1. Press the [CBL] button to select the CBL mode
          2. Press the BLANK button and [SELECT] button simultaneously for 3 seconds. The [CBL] device LED will turn on for 20 seconds
          3. Press up to 10 buttons you wish to store. The [CBL] device LED will blink once for each command entered
          4. Press the [CH?] button to store the functions that were selected. The [CBL] device LED will blink twice to confirm the storage of functions

        Low Battery Warning

          When the battery is low, the remote control LED blinks 2 times whenever a [Device] button is pressed to turn on equipment.

        Memory Lock

          This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.

        Button Functions

          Remote Controls for CA, OR and WA (311)

        UR4U-MDVR-CHD2


        View printable manual

        • UR4U-MDVR-CHD2

        Remote Controls for CA, OR and WA (312)

        Expand All | CollapseAll

        Quick Set-Up Method

          1. Turn on the device you want to program to program your TV, turn the TV on
          2. Point the remote at the TV and press and hold the TV key for 3 seconds. While Holding the TV key, the TV LED will light off and on again
          3. Begin to press the number keys, one at a time, starting with 1, then 2, 3, 4, 5, 6, 7, 8, 9, 0 until the TV turns off
          4. Release the TV key to save the code. The TV LED will blink twice to confirm the code is stored. Repeat these steps for your DVD, Aux, etc

        Three-Digit Code Programming Method

          1. Turn on the device you want to program (TV, DVD or AUX)
          2. Press the [Device] button (TV, DVD or AUX) to be programmed and [OK/SEL] button simultaneously for 3 seconds. The device LED will light for 30 seconds indicating the unit is ready to be programmed
          3. Point the remote control toward the device and enter the 3-digit code number assigned to your brand

            TV -- >

            DVD (use DVD key) -- >

            DVD Recorders (use DVD key) -- >

            TV/DVD Combos (use DVD key) -- >

            DVD/VCR Combos (use DVD key) -- >

            TV/VCR Combos (use DVD key) -- >

            VCR (use DVD key) -- >

            TV/DVD/VCR Combos (use DVD key) -- >

            Audio Device (use AUX key) -- >

            TiVo (use AUX key) -- >

            iPod Controls (use AUX key) -- >

            Media PCs (use AUX key) -- >

            Gaming Systems (use AUX key) -- >

            Lighting Controls (use AUX key) -- >

            Digital to Analog Converter box (use AUX key) -- >

            • If the 3-digit code number you just entered is correct, the device will turn Off
            • If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off
          4. After you’ve entered the correct code number and the device has turned Off, press the [POWER] button to turn the device back On. Now it’s time to test the VOLUME and MUTE buttons for the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all work
          5. If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand
          6. Once you have found the correct 3-digit code, save it by pressing the same [DEVICE] button one more time
          7. The [Device] LED light will blink twice to confirm that the code was successfully stored

        Auto Search Method

          If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:

          1. Turn on the equipment you wish to operate
          2. Pressthe [DEVICE] button and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
            • The device LED will light on for 30 seconds. The next step must be entered while LED is on
          3. Press the [CH?] or [CH?] button one step at a time or keep it pressed. The remote will emit a series of Power ON/OFF commands. Release the [CH?] or [CH?] button as soon as the equipment turns off.
          4. Verify that you selected the correct code by pressing [POWER] again. The equipment should either turn on or turn off
          5. Press the [Device] button to store the code. The Device LED will blink twice to confirm that the code has been stored

        Code NumberReadback

          1. Press the [Device] button and [OK/SEL] simultaneously for 3 seconds
          2. The device LED will light on for 30 seconds. The next step must be entered while LED is on
          3. Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code number
            • Each digit is separated by 1 second. Ten blinks is equal to the number 0
            • For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks

        Programming a4th Device toAUX Button

          You can take advantage of the AUX function to program a 4th Component such as a second TV, VCR, DVD or Audio Component

          1. Turn on the equipment you wish to operate
          2. Press [AUX] and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
            • The device LED will light on for 30 seconds. The next step must be entered while LED is on
          3. Press the [Device] button you want to setup. Point the remote control toward the Device and enter the 3-digit code number assigned to your brand

            TV -- >

            DVD (use DVD key) -- >

            DVD Recorders (use DVD key) -- >

            TV/DVD Combos (use DVD key) -- >

            DVD/VCR Combos (use DVD key) -- >

            TV/VCR Combos (use DVD key) -- >

            VCR (use DVD key) -- >

            TV/DVD/VCR Combos (use DVD key) -- >

            Audio Device (use AUX key) -- >

            TiVo (use AUX key) -- >

            iPod Controls (use AUX key) -- >

            Media PCs (use AUX key) -- >

            Gaming Systems (use AUX key) -- >

            Lighting Controls (use AUX key) -- >

            Digital to Analog Converter box (use AUX key) -- >

          4. If the 3-digit code number you just entered is the correct number, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off
          5. Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, you need to find a new code.
          6. Press [AUX] one more time. The Device LED light will blink twice to confirm the code was stored

        Programming the System On/Off Button

          The System on/off button can send out up to three power on/off commands for the devices you programmed into the remote control

          1. Press [CBL]
          2. Press [System On/Off] and [OK/SEL] simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds
          3. Press [TV]
          4. Press [DVD] (if adding)
          5. Press [AUX] (if adding)
          6. Press [CH?] to save the power commands you stored. The [CBL] button will blink twice to confirm

        Programming Channel Controls

          Channel controls (CH?, CH?, LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:

          CBL : CBL TV : CBL DVD : DVD AUX : AUX

          If you wish to store the TV channel controls in TV mode, use the following steps

          1. Press the [OK/SEL] button and [TV] button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while the LED is on
          2. Press the [VOL?] button. The device LED will blink
          3. Press [TV] button. The device LED will blink twice to confirm the programming

            To return TV device to CBL channel repeat steps above replacing [TV] with [CBL] in Step 3

        Volume Control

          Volume and Mute control are factory programmed to the respective Device mode you select, as follows:

          CBL : TV TV : TV DVD : TV AUX : AUX

          If you wish to store the Cable volume control in CBL mode, use the following steps

          1. Press [CBL] button and [OK/SEL] simultaneously for three seconds
            • The device LED will turn on for 20 seconds. The next step must be performed while the LED is on
          2. Press the [VOL?] button. The device LED will blink
          3. Press [CBL] button. The device LED will blink twice to confirm the programming

          To restore the volume control back to your TV in CBL mode, repeat the above steps by replacing [CBL] with [TV] in Step 3

        Low Battery Warning

          When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.

        Memory Lock

          This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.

        Button Functions

          Remote Controls for CA, OR and WA (313)

        CLIKR-5 (UR5L-6200L)


        View printable manual

        • CLIKR-5 (UR5L-6200L)

        Remote Controls for CA, OR and WA (314)

        Expand All | CollapseAll

        Three-Digit Code Programming Method

          1. Turn on the device you want to program (TV, DVD, VCR or AUX)
          2. Press the [Device] button (TV, DVD, VCR or AUX) to be programmed and [OK/SEL] button simultaneously for 3 seconds. The device LED will light for 30 seconds indicating the unit is ready to be programmed
          3. Point the remote control toward the device and enter the 3-digit code number assigned to your brand
            TV -- > VCR (use VCR key) -- > TV/VCR Combos (use VCR key) -- > DVD (use DVD key) -- > DVD Recorders (use DVD key) -- > TV/DVD Combos (use DVD key) -- > TV/DVD/VCR Combos (use DVD key) -- > DVD/VCR Combos (use DVD key) -- > Audio Device (use AUX key) -- > TiVo (use AUX key) -- >
            • If the 3-digit code number you just entered is correct, the device will turn Off
            • If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off
          4. After you’ve entered the correct code number and the device has turned Off, press the [POWER] button to turn the device back On. Now it’s time to test the VOLUME and MUTE buttons for the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all work
          5. If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand
          6. Once you have found the correct 3-digit code, save it by pressing the same [Device] button one more time
          7. The [Device] LED light will blink twice to confirm that the code was successfully stored

        Auto Search Method

          If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:

          1. Turn on the equipment you wish to operate
          2. Pressthe [Device] button and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
            • The device LED will light on for 30 seconds. The next step must be entered while LED is on
          3. Press the [CH?] or [CH?] button one step at a time or keep it pressed. The remote will emit a series of Power ON/OFF commands. Release the [CH?] or [CH?] button as soon as the equipment turns off.
          4. Verify that you selected the correct code by pressing [POWER] again. The equipment should either turn on or turn off
          5. Press the [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored

        Code NumberReadback

          1. Press the [Device] button and [OK/SEL] simultaneously for 3 seconds
          2. The device LED will light on for 30 seconds. The next step must be entered while LED is on
          3. Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code number
            • Each digit is separated by 1 second. Ten blinks is equal to the number 0
            • For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks

        The Learning Method

          1. Press the [Device] button (AUX, TV, VCR or DVD) to be programmed and the [ASPECT] buttons simultaneously for 3 seconds until the Device LED light turns on
          2. Line up the CLIKR-5 to the other remote, head-to-head, 1 or 2 inches apart
          3. Press any button on the CLIKR-5 that you want to teach a command to. For example, if you want to teach the [MUTE] button, press the [MUTE] button
          4. Press and hold the [MUTE] button on the other remote until the CLIKR-5 Device LED light blinks twice The LED will blink 5 times if there was an error in the learning process. In so, repeat STEPS 3 and 4. Continue learning other buttons by repeating steps 3 and 4
          5. Once you have completed teaching CLIKR-5 all desired commands for that Device, save the learned commands by pressing the [Device] and [ASPECT] buttons simultaneously until the Device LED blinks 3 times. Now test all the buttons to make sure they learned correctly

          Erasing a Single Learned Command

          1. Press the [Device] and [ASPECT] buttons simultaneously for 3 seconds until the Device LED light turns on
          2. Press and hold the button you want to erase for 3 seconds. The Device LED will blink twice to confirm the erasure
          3. To exit, press and hold both the [Device] and [ASPECT] buttons simultaneously until the Device LED blinks 3 times

          Erasing All Learned Commands from One Device

          1. Press the [Device] and [ASPECT] buttons simultaneously for 3 seconds until the Device LED light turns on
          2. Press and hold both the [Device] button you want to erase and the [PAUSE] button for 5 seconds. The Device LED will blink twice to confirm the erasure
          3. To exit, press and hold both the [Device] and [ASPECT] buttons simultaneously until the Device LED blinks 3 times

        Programming a5th Device toAUX Button

          You can take advantage of the AUX function to program a 4th Component such as a second TV, VCR, DVD or Audio Component

          1. Turn on the equipment you wish to operate
          2. Press [AUX] and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
            • The device LED will light on for 30 seconds. The next step must be entered while LED is on
          3. Press the [Device] button you want to setup. Point the remote control toward the Device and enter the 3-digit code number assigned to your brand
            TV -- > VCR (use VCR key) -- > TV/VCR Combos (use VCR key) -- > DVD (use DVD key) -- > DVD Recorders (use DVD key) -- > TV/DVD Combos (use DVD key) -- > TV/DVD/VCR Combos (use DVD key) -- > DVD/VCR Combos (use DVD key) -- > Audio Device (use AUX key) -- > TiVo (use AUX key) -- >
          4. If the 3-digit code number you just entered is the correct number, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off
          5. Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, you need to find a new code.
          6. Press [AUX] one more time. The Device LED light will blink twice to confirm the code was stored

        Programming the System On/Off Button

          The System on/off button can send out up to three power on/off commands for the devices you programmed into the remote control

          1. Press [CBL]
          2. Press [System On/Off] and [OK/SEL] simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds
          3. Press [TV]
          4. Press [DVD] (if adding)
          5. Press [VCR] (if adding)
          6. Press [AUX] (if adding)
          7. Press [CH?] to save the power commands you stored. The [CBL] button will blink twice to confirm

        Programming Channel Controls

          Channel controls (CH?, CH?, LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:

          CBL : CBL TV : CBL VCR : CBL DVD : DVD AUX : AUX
          If you wish to store the TV channel controls in TV mode, use the following steps

          1. Press the [OK/SEL] button and [TV] button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while the LED is on
          2. Press the [VOL?] button. The device LED will blink
          3. Press [TV] button. The device LED will blink twice to confirm the programming

            To return TV device to CBL channel repeat steps above replacing [TV] with [CBL] in Step 3

        Volume Control

          Volume and Mute control are factory programmed to the respective Device mode you select, as follows:

          CBL : TV TV : TV VCR : TV DVD : TV AUX : AUX
          If you wish to store the Cable volume control in CBL mode, use the following steps

          1. Press [CBL] button and [OK/SEL] simultaneously for three seconds
            • The device LED will turn on for 30 seconds. The next step must be performed while the LED is on
          2. Press the [VOL?] button. The device LED will blink
          3. Press [CBL] button. The device LED will blink twice to confirm the programming

          To restore the volume control back to your TV in CBL mode, repeat the above steps by replacing [CBL] with [TV] in Step 3

        Macro Buttons

          In the CABLE device mode, the [M1], [M2], and [HELP] (see button functions below) can be programmed to act as a 'Favorite Channel' button.

          This allows you to program up to 10 commands with one button press.

          1. Press the [CBL] button to select the CBL mode
          2. Press the [Macro] button and [OK/SEL] button simultaneously for 3 seconds. The [CBL] button will turn on for 20 seconds
            • The [Macro] button will turn on for 30 seconds. The next step must be performed while the LED is on
          3. Press up to 10 buttons you wish to store. The [CBL] Component LED will blink once for each command entered
          4. Press the [CH?] button to store the commands that were selected. The [CBL] button will blink twice to confirm the storage of commands

          To erase the Macro programming and return to the original function:

          1. Press the [CBL] button to select the CABLE mode
          2. Press a [Macro] button and the [OK/SEL] button simultaneously for 3 seconds
            • The CBL device LED will turn on for 30 seconds. The next step must be performed while the LED is on
          3. Press the [CH?] button to erase the functions stored in the button. The CBL button will blink twice to confirm that the memory button has been erased

        Low Battery Warning

          When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.

        Memory Lock

          This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.

        Button Functions

          Remote Controls for CA, OR and WA (315)

        CLIKR-5 (UR5U-6200)


        View printable manual

        • CLIKR-5 (UR5U-6200)

        Remote Controls for CA, OR and WA (316)

        Expand All | CollapseAll

        Three-Digit Code Programming Method

          1. Turn on the device you want to program (TV, DVD or AUX)
          2. Press the [DEVICE] button (TV, DVD or AUX) to be programmed and [OK/SEL] button simultaneously for 3 seconds. The device LED will light for 30 seconds indicating the unit is ready to be programmed
          3. Point the remote control toward the device and enter the 3-digit code number assigned to your brand

            TV ?
            VCR (use VCR key) ?
            TV/VCR (use VCR key) ?
            DVD (use DVD key) ?
            TV/DVD Combos (use DVD key) ?
            TV/DVD/VCR Combos (use DVD key) ?
            DVD/VCR Combos (use DVD key) ?
            DVD Recorders (use DVD key) ?
            Audio Device (use AUX key) ?
            TiVo (use AUX key) ?

            • If the 3-digit code number you just entered is correct, the device will turn Off
            • If it did not turn Off, continue entering code numbers listed for that brand until the device turns Off
          4. After you’ve entered the correct code number and the device has turned Off, press the [POWER] button to turn the device back On. Now it’s time to test the VOLUME and MUTE buttons for the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all work
          5. If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand
          6. Once you have found the correct 3-digit code, save it by pressing the same [DEVICE] button one more time. The [DEVICE] LED light will blink twice to confirm that the code was successfully stored

        Auto Search Method

          If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:

          1. Turn on the equipment you wish to operate
          2. Pressthe [DEVICE] button and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
            • The device LED will light on for 30 seconds. The next step must be entered while LED is on
          3. Press the [CH?] or [CH?] button one step at a time or keep it pressed. The remote will emit a series of Power ON/OFF commands. Release the [CH?] or [CH?] button as soon as the equipment turns off.
          4. Verify that you selected the correct code by pressing [POWER] again. The equipment should either turn on or turn off
          5. Press the [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored

        Code NumberReadback

          1. Press the [DEVICE] button and [OK/SEL] simultaneously for 3 seconds

            The device LED will light on for 30 seconds. The next step must be entered while LED is on

          2. Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code number
            • Each digit is separated by 1 second. Ten blinks is equal to the number 0
            • For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks

        Programming a5th Device toAUX Button

          You can take advantage of the AUX function to program a 4th Component such as a second TV, VCR, DVD or Audio Component

          1. Turn on the equipment you wish to operate.
          2. Press [AUX] and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
            • The device LED will light on for 20 seconds. The next step must be entered while LED is on
          3. Press the desired [DEVICE] button. Point the remote control toward the device and enter the 3-digit code number assigned to your brand

            TV ?
            VCR (use VCR key) ?
            TV/VCR (use VCR key) ?
            DVD (use DVD key) ?
            TV/DVD Combos (use DVD key) ?
            TV/DVD/VCR Combos (use DVD key) ?
            DVD/VCR Combos (use DVD key) ?
            DVD Recorders (use DVD key) ?
            Audio Device (use AUX key) ?
            TiVo (use AUX key) ?

          4. If the 3-digit code number you just entered is the correct number, the device will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the device turns Off
          5. Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, you need to find a new code
          6. Press [AUX] one more time. The desired [DEVICE] LED light will blink twice to confirm the code was stored

        Programming the System On/Off Button

          The System on/off button can send out up to five power on/off commands for the devices you programmed into the remote control

          1. Press [CBL]
          2. Press [System On/Off] and [OK/SEL] simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds
          3. Press [TV]
          4. Press [DVD] (if adding)
          5. Press [VCR] (if adding)
          6. Press [AUX] (if adding)
          7. Press [CH?] to save the power commands you stored. The [CBL] button will blink twice to confirm

        Programming Channel Controls

          Channel controls (CH?, CH?, LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:

          CBL : CBL TV : CBL VCR : CBL DVD : DVD AUX : AUX

          If you wish to store the TV channel controls in TV mode, use the following steps

          1. Press [TV] and [OK/SEL] button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while the LED is on
          2. Press the [VOL?] button. The device LED will blink
          3. Press [TV] button. The device LED will blink twice to confirm the programming

            To return TV device to CBL channel repeat steps above replacing [TV] with [CBL] in Step 3

        Volume Control

          Volume and Mute control are factory programmed to the respective Device mode you select, as follows:

          CBL : TV TV : TV DVD : TV AUX : AUX

          If you wish to store the Cable volume control in CBL mode, use the following steps

          1. Press [CBL] and [OK/SEL] simultaneously for three seconds
            • [CBL] will turn on for 20 seconds. The next step must be performed while the LED is on
          2. Press the [VOL?] button. The device LED will blink
          3. Press [CBL] button. The device LED will blink twice to confirm the programming

          To restore the volume control back to your TV in CBL mode, repeat the above steps by replacing [CBL] with [TV] in Step 3

        Programming For Advanced Function (blank key)

          In the CBL mode, the M1, M2, Help, BLANK buttons can be programmed to act as a macro or favorite channel button. You can send out up to ten commands with one button press

          1. Press the [CBL] button to select the CBL mode
          2. Press the [Macro] button and [OK/SEL] button simultaneously for 3 seconds. The [CBL] device LED will turn on for 20 seconds
          3. Press up to 10 buttons you wish to store. The [CBL] device LED will blink once for each command entered
          4. Press the [CH?] button to store the functions that were selected. The [CBL] device LED will blink twice to confirm the storage of functions

        Low Battery Warning

          When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.

        Memory Lock

          This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.

        Button Functions

          Remote Controls for CA, OR and WA (317)

        ENT MOTO


        View printable manual

        • ENT MOTO

        Remote Controls for CA, OR and WA (318)

        Expand All | CollapseAll


        Automatic Programming

          The SmartScan™ programming instructions can also be found on the battery cover of the remote control. SmartScan™ will allow you to easily try all the available programming codes for the selected device and find the best match. If you prefer manual programming or already have the device codes see the Manual Programming section below

          1. Turn on the device
          2. Pressing and hold the desired device key (AUX, AUD, VCR, CBL, DVD, TV) until all device keys on the remote begin to flash
            (approximately 3 seconds), then release the key
          3. If the device you’re are attempting to program matches the selected device key (e.g. TV = TV key) proceed to step 5

          4. If the device you’re are attempting to program does not match the selected key (e.g. a second VCR = AUX key), locate the correct prefix code for the device you wish to program (listed below). Press and release the number key that matches the prefix code
            Prefix: Device:
            0 Television
            1 DVD Player, VCR, or PVR
            4 Audio Device
            5 Combo Units

          5. Press and release the POWER key. The device key will stop flashing and remain on
          6. Point the remote control at the selected device
          7. Press and hold the UP ARROW key until the device turns off. While holding the UP ARROW key the remote will send a new code approximately once every second. The device button will blink each time a new code is sent. If you pass the code that turns off the device, press the DOWN ARROW key to return to the previous code
          8. When the device turns off, you have found a candidate code. Press the POWER Key to turn device back on. Test various functions using the remote control to determine if this code will work. If primary functions do not work, make sure the device is still on then resume SmartScan™ by pressing the UP ARROW key to find another device code
          9. Once you have found a satisfactory code, press OK to lock the code. The power of the device must be on. The device key will then flash three times. Go to section 10 to recall and record your device codes. When all the codes have been attempted the device button will flash rapidly

        Manual Programming

          To manually set up the Enterprise to operate a device, find the manufacturer of the device in the list of manufacturers’ codes

          1. Press and hold the device key to be programmed until all device keys begin to flash (approximately 3 seconds). Release the key. The selected device key will continue to flash
          2. Enter the four digit code for the desired device using the number keys. After pressing the first digit, the device key should light and remain on if the programming is successful. After the last digit is pressed the device key should flash three times and turn off

            Audio Device -- >

            TV/DVD & TV/VCR Combos -- > TV -- >

            VCR/DVD/PVR -- >

          3. Test the code by trying various functions. If the primary function keys fail to respond satisfactorily try the next code listed for the manufacturer

            If you have tried all the codes listed for the manufacturer and the device does not respond, try to program the device using Automatic Programming above

        Recalling a Device Code

          Use the following steps to read the code set for a device. This is useful for determining a device code that was set using Automatic Programming above

          1. Press and hold the device key to be read until all device keys begin to flash (approximately 3 seconds). Release the key. The selected device key will continue to flash
          2. Press and release the OK key. The device key flashes each of the four digits in the code. A pause separates each digit. For example, three flashes represent the number 3, and a rapid flicker represents 0. A code of 1032 will be shown as:

            FLASH < pause> FLICKER < pause> FLASH, FLASH, FLASH < pause> FLASH, FLASH

            Count and record the sequence of flashes to determine the four-digit code

        ProgrammingVolume Control

          By default, your Enterprise remote controls cable volume through the Cable Box, and the VCR and DVD through the Television. To allow volume control through a different device:

          1. Press and hold the CBL device key until all the device keys begin to flash. Release the CBL key. The CBL key will continue to flash
          2. Press and release the VOLUME UP key, the CBL key will remain on
          3. Press and release the VOLUME DOWN key. The CBL key will turn off when VOLUME DOWN is pressed, and will turn on when released
          4. Press and release the key corresponding to the device you wish to use to control volume (TV or AUD). After you release the key, the CBL key will flash three times and turn off

          To return volume control to the default state:

          1. Press and hold the CBL device key until all the device keys begin to flash. Release the CBL key. The CBL key will continue to flash
          2. Press and release the VOLUME UP key. The CBL device key will stop flashing and stay on
          3. Press and release the VOLUME DOWN key, and then press and release the OK key
          4. After you release the OK key, the CBL device key will flash three times and turn off

        Master Power Control

          The Master Power function allows you to turn off and on two or more devices simultaneously with a single press of the POWER button. The following steps describe how to program the Master Power Control function:

          1. Press and hold the CBL device key until all the device keys begin to flash. Release the CBL key. The CBL key will continue to flash
          2. Press and release the POWER key
          3. Individually press and release each device key corresponding to the components you wish to be controlled by Master Power (starting with the cable device key)

            NOTE: If no keys are pressed in this step, no change will occur


          4. Press and release the POWER key. The CBL key will flash three times and turn off
          5. Manually turn on all devices. Then test the Master Power control by pressing the POWER key

          To disable Master Power, repeat the previous steps selecting only one device for Master Power (any device can be selected). The remote will now control the power ON/OFF of each device separately.

          NOTE: Once Master Power has been programmed for two or more devices, pressing the POWER key in normal operation will cause the remote to transmit the POWER on/off commands for those devices selected during Master Power programming.
          To override this and transmit a POWER on/off command for a device not included in the Master Power selection, press the DEVICE key for that device and immediately press the POWER key.

        Channel Lock

          Channel Lock causes channel up and down functions to always operate the settop box independent of the device (TV, CBL, VCR, DVD or AUD) currently selected. The remote comes with Channel Lock activated. If you want the remote control to operate the channel function on your TV or VCR, you will need to deactivate Channel Lock:

          1. Press and hold the CBL device key until all the device keys begin to flash (approximately 3 seconds). Release the CBL key. The CBL key will continue to flash
          2. Press and release the CHANNEL UP key
          3. Press and release the CHANNEL DOWNkey
          4. Press the OK key. The CBL device key will flash three times to confirm

          Repeat these steps to reactivate Channel Lock

        Button Descriptions

          Remote Controls for CA, OR and WA (319)

        UR4-EXP


        View printable manual

        • UR4-EXP

        Remote Controls for CA, OR and WA (320)

        Expand All | CollapseAll

        Three-Digit Code Programming Method

          1. Turn on the equipment you wish to program. (TV, VCR, or DVD)
          2. Press the [Device] button (AUX, VCR, or TV) and [SELECT] simultaneously for 3 seconds. The device LED will turn on indicating the unit is ready to be programmed
            • The [Device] button will stay lit for 20 seconds. The next step must be entered while the LED is on
          3. Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. The equipment will turn off when the correct three-digit code number has been entered

            TV -- >

            VCR, TV/VCR* (using VCR key) -- >

            DVD, TV/DVD* (using VCR key) -- >

            Audio Device (using AUX key) -- >

            TiVo (using AUX key) -- >

            DMX & DCR (using AUX key) -- >

          4. Verify you have selected the correct code by pressing the [POWER] button, the equipment should turn on or turn off
          5. Press the [Device] button again. The device LED will blink twice to confirm that the code has been stored


          *To operate the volume control on TV/VCR & TV/DVD combination units, see Volume Control below

        Auto Search Method

          If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:

          1. Turn on the equipment you wish to operate
          2. Press the [Device] button and [SELECT] simultaneously for 3 seconds. The device LED will turn on
            • The device LED will light on for 20 seconds. The next step must be entered while LED is on
          3. Press the [CHANNEL UP] or [CHANNEL DOWN] button one step at a time or keep it pressed. The remote will emit a series of Power ON/OFF commands. Release the [CHANNEL UP] or [CHANNEL DOWN] button as soon as the equipment turns off.
          4. Verify that you selected the correct code by pressing [POWER] again. The equipment should either turn on or turn off
          5. Press the [Device] button to store the code. The Device LED will blink twice to confirm that the code has been stored

        Code Number Readback

          1. Press the [Device] button and [SELECT] simultaneously for 3 seconds
          2. The device LED will light on for 20 seconds. The next step must be entered while LED is on
          3. Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code number
            • Each digit is separated by 1 second. Ten blinks is equal to the number 0
            • For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks

        Programming a Second TV to AUX Button

          1. Press [AUX] and [SELECT] simultaneously for 3 seconds. The device LED will turn on
            • The device LED will light on for 20 seconds. The next step must be entered while LED is on
          2. Press [TV] to pick up the TV code table
          3. Point the remote control toward the equipment and enter the three-digit code number assigned to your TV brand from the code tables. The equipment will turn off when the correct three-digit code number has been entered

            TV -- >

          4. Press [VCR] once again. The device LED will blink twice to confirm that the code has been stored

        Programming the System On/Off Button

          The System on/off button can send out up to three power on/off commands for the devices you programmed into the remote control

          1. Press [CBL]
          2. Press [System On/Off] and [SELECT] simultaneously for 3 seconds. The [CBL] button will turn on for 20 seconds
          3. Press [TV]
          4. Press [VCR] (if adding)
          5. Press [AUX] (if adding)
          6. Press [CHANNEL UP] to save the power commands you stored. The [CBL] button will blink twice to confirm

        Programming Channel Controls

          Channel controls (CHANNEL UP, CHANNEL DOWN LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:

          CBL : CBL TV : CBL VCR : VCR AUX : AUX

          If you wish to store the TV channel controls in TV mode, use the following steps

          1. Press the [SELECT] button and [TV] button simultaneously for three seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on
          2. Press the [VOLUME DOWN] button. The device LED will blink
          3. Press [TV] button. The device LED will blink twice to confirm the programming

            To return TV device to CBL channel repeat steps above replacing [TV] with [CBL] in Step 3

        Volume Control

          Volume and Mute control are factory programmed to the respective Device mode you select, as follows:

          CBL : TV TV : TV VCR : TV AUX : AUX

          If you wish to store the Cable volume control in CBL mode, use the following steps

          1. Press [CBL] button and [SELECT] simultaneously for three seconds
            • The device LED will turn on for 20 seconds. The next step must be performed while the LED is on
          2. Press the [VOLUME UP] button. The device LED will blink
          3. Press [CBL] button. The device LED will blink twice to confirm the programming

          To restore the volume control back to your TV in CBL mode, repeat the above steps byreplacing [CBL] with [TV] in Step 3.

          To operate the volume control for TV/VCR & TV/DVD combination units, Please use following steps

          1. Press [CBL] button and [SELECT] simultaneously for 3 seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on
          2. Press the [VOLUME UP] button
          3. Press the [VCR] button. The device LED will blink twice to confirm the programming

        Low Battery Warning

          When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.

        Memory Lock

          This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.

        Button Functions

          Remote Controls for CA, OR and WA (321)

        UR3-EXP


        View printable manual

        • UR3-EXP

        Remote Controls for CA, OR and WA (322)

        Expand All | CollapseAll

        Three-Digit Code Programming Method

          1. Turn on the equipment you wish to program. (TV, VCR, or DVD)
          2. Press [TV] ( or [VCR]) and [SELECT] simultaneously for 3 seconds. The device LED will turn on indicating the unit is ready to be programmed
            • [TV] ( or [VCR]) key will stay lit for 20 seconds. The next step must be entered while the LED is on
          3. Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. The equipment will turn off when the correct three-digit code number has been entered.
            TV -- >

            VCR -- > DVD (using VCR key) -- >

          4. Verify you have selected the correct code by pressing the [MUTE] button, the equipment should turn on or turn off
          5. Press [TV] ( or [VCR]) again. The device LED will blink twice to confirm that the code has been stored

          Please Note:

          • Try all the functions on the remote control. If any of the functions do not work as they should, repeat from Step 2 using the next three-digit code number from the same brand list. Make sure that the VCR/VOD key is in the VCR position when using your VCR
          • For TV/VCR combination unit, Please set up TV code number in the TV mode to operate the volume, Set up VCR code number in the VCR mode to operate the VCR functions.

        Auto Search Method

          If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:

          1. Turn on the equipment you wish to operate
          2. Press [TV] ( or [VCR]) and [SELECT] simultaneously for 3 seconds. The device LED will turn on
            • The device LED will light on for 20 seconds. The next step must be entered while LED is on
          3. Point the remote control toward the equipment, press [CH?], then [MUTE] repeatedly until the equipment turns off
          4. Verify that you selected the correct code by pressing [MUTE] again. The equipment should either turn on or turn off
          5. Press [TV] (or [VCR]) key to store the code. The Device LED will blink twice to confirm that the code has been stored

        Code NumberReadback

          1. Press [TV] ( or [VCR]) and [SELECT] simultaneously for 3 seconds
          2. The device LED will light on for 20 seconds. The next step must be entered while LED is on
          3. Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code number
            • Each digit is separated by 1 second. Ten blinks is equal to the number 0
            • For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks

        Programming a Second TV to VCR key

          1. Press [VCR] and [SELECT] simultaneously for 3 seconds. The device LED will turn on
            • The device LED will light on for 20 seconds. The next step must be entered while LED is on
          2. Press [TV] to pick up the TV code table
          3. Point the remote control toward the equipment and enter the three-digit code number assigned to your TV brand from the code tables. The equipment will turn off when the correct three-digit code number has been entered.
            TV -- >
          4. Press [VCR] once again. The device LED will blink twice to confirm that the code has been stored

        Programming the System On/Off Button

          The System on/off button can send out up to three power on/off commands for the devices you programmed into the remote control

          1. Press [CBL]
          2. Press [System On/Off] and [SELECT] simultaneously for 3 seconds. The [CBL] button will turn on for 20 seconds
          3. Press [TV]
          4. Press [VCR] (if adding)
          5. Press [CH?] to save the power commands you stored. The [CBL] button will blink twice to confirm

        Volume Control

          When in [CBL] mode, the default volume control is through your TV. If you wish to control the Converter volume control instead, use the following steps

          1. Press [CBL] and [SELECT] simultaneously for 3 seconds
            • [CBL] will light on for 20 seconds. The next step must be entered while the LED is on
          2. Press [VOL?]
          3. Press [CBL]. [CBL] will blink twice to confirm the programming

          To restore the volume control back to your TV in CBL mode, repeat the above steps by pressing [TV] in Step 3

        Low Battery Warning

          When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.

        Memory Lock

          This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.

        Button Functions

          Remote Controls for CA, OR and WA (323)

        UR4-DCT


        View printable manual

        • UR4-DCT

        Remote Controls for CA, OR and WA (324)

        Expand All | CollapseAll

        Three-Digit Code Programming Method

          1. Turn on the equipment you wish to program. (TV, VCR, or DVD)
          2. Press the [Device] button (AUX, VCR, or TV) and [OK] simultaneously for 3 seconds. The device LED will turn on indicating the unit is ready to be programmed
            • The [Device] button will stay lit for 20 seconds. The next step must be entered while the LED is on
          3. Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. The equipment will turn off when the correct three-digit code number has been entered.
            TV -- >

            VCR, TV/VCR* (using VCR key) -- > DVD, TV/DVD* (using VCR key) -- > Auxiliary Device (using AUX key) -- > DMX & DCR (using AUX key) -- >

          4. Verify you have selected the correct code by pressing the [POWER] button, the equipment should turn on or turn off
          5. Pressthe [Device] button again. The device LED will blink twice to confirm that the code has been stored


          *To operate the volume control on TV/VCR & TV/DVD combination units, see Volume Control below

        Auto Search Method

          If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:

          1. Turn on the equipment you wish to operate
          2. Pressthe [Device] button and [OK] simultaneously for 3 seconds. The device LED will turn on
            • The device LED will light on for 20 seconds. The next step must be entered while LED is on
          3. Press the [CH?] or [CH?] button one step at a time or keep it pressed. The remote will emit a series of Power ON/OFF commands. Release the [CH?] or [CH?] button as soon as the equipment turns off.
          4. Verify that you selected the correct code by pressing [POWER] again. The equipment should either turn on or turn off
          5. Press the [Device] button to store the code. The Device LED will blink twice to confirm that the code has been stored

        Code NumberReadback

          1. Press the [Device] button and [OK] simultaneously for 3 seconds
          2. The device LED will light on for 20 seconds. The next step must be entered while LED is on
          3. Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code number
            • Each digit is separated by 1 second. Ten blinks is equal to the number 0
            • For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks

        Programming a Second TV toAUX Button

          1. Press [AUX] and [OK] simultaneously for 3 seconds. The device LED will turn on
            • The device LED will light on for 20 seconds. The next step must be entered while LED is on
          2. Press [TV] to pick up the TV code table
          3. Point the remote control toward the equipment and enter the three-digit code number assigned to your TV brand from the code tables. The equipment will turn off when the correct three-digit code number has been entered.
            TV -- >
          4. Press [VCR] once again. The device LED will blink twice to confirm that the code has been stored

        Programming the System On/Off Button

          The System on/off button can send out up to three power on/off commands for the devices you programmed into the remote control

          1. Press [CBL]
          2. Press [System On/Off] and [OK] simultaneously for 3 seconds. The [CBL] button will turn on for 20 seconds
          3. Press [TV]
          4. Press [VCR] (if adding)
          5. Press [AUX] (if adding)
          6. Press [CH?] to save the power commands you stored. The [CBL] button will blink twice to confirm

        Programming Channel Controls

          Channel controls (CH?, CH?, LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:

          CBL : CBL TV : CBL VCR : VCR AUX : AUX
          If you wish to store the TV channel controls in TV mode, use the following steps.

          1. Press the [OK] button and [TV] button simultaneously for three seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on

          2. Press the [VOL?] button. The device LED will blink

          3. Press [TV] button. The device LED will blink twice to confirm the programming

          To return TV device to CBL channel repeat steps above replacing [TV] with [CBL] in Step 3

        Volume Control

          Volume and Mute control are factory programmed to the respective Device mode you select, as follows:

          CBL : TV TV : TV VCR : TV AUX : AUX
          If you wish to store the Cable volume control in CBL mode, use the following steps

          1. Press the [OK] button and [CBL] button simultaneously for three seconds
            • The device LED will turn on for 20 seconds. The next step must be performed while the LED is on
          2. Press the [VOL?] button. The device LED will blink
          3. Press [CBL] button. The device LED will blink twice to confirm the programming

          To restore the volume control back to your TV in CBL mode, repeat the above steps by replacing [CBL] with [TV] in Step 3. To operate the volume control for TV/VCR & TV/DVD combination units, Please use following steps

          1. Press the [CBL] button and the [OK] button simultaneously for 3 seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on
          2. Press the [VOL?] button
          3. Press the [VCR] button. The device LED will blink twice to confirm the programming

        Low Battery Warning

          When the battery is low, the remote control LED blinks 2 times whenever a [Device] button is pressed to turn on equipment.

        Memory Lock

          This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.

        Button Functions

          Remote Controls for CA, OR and WA (325)

        UR4-DSR


        View printable manual

        • UR4-DSR

        Remote Controls for CA, OR and WA (326)

        Expand All | CollapseAll

        Three-Digit Code Programming Method

          1. Turn on the equipment you wish to program. (TV, VCR, or DVD)
          2. Press the [Device] button (AUX, VCR, or TV) and [ENTER] simultaneously for 3 seconds. The device LED will turn on indicating the unit is ready to be programmed
            • The [Device] button will stay lit for 20 seconds. The next step must be entered while the LED is on
          3. Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. The equipment will turn off when the correct three-digit code number has been entered.
            TV -- >

            VCR, TV/VCR* (using VCR key) -- > DVD, TV/DVD* (using VCR key) -- > Audio Device (using AUX key) -- > TiVo (using AUX key) -- > DMX & DCR (using AUX key) -- >

          4. Verify you have selected the correct code by pressing the [POWER] button, the equipment should turn on or turn off
          5. Pressthe [Device] button again. The device LED will blink twice to confirm that the code has been stored


          *To operate the volume control on TV/VCR & TV/DVD combination units, see Volume Control below

        Auto Search Method

          If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:

          1. Turn on the equipment you wish to operate
          2. Pressthe [Device] button and [ENTER] simultaneously for 3 seconds. The device LED will turn on
            • The device LED will light on for 20 seconds. The next step must be entered while LED is on
          3. Press the [CH?] or [CH?] button one step at a time or keep it pressed. The remote will emit a series of Power ON/OFF commands. Release the [CH?] or [CH?] button as soon as the equipment turns off.
          4. Verify that you selected the correct code by pressing [POWER] again. The equipment should either turn on or turn off
          5. Press the [Device] button to store the code. The Device LED will blink twice to confirm that the code has been stored

        Code NumberReadback

          1. Press the [Device] button and [ENTER] simultaneously for 3 seconds
          2. The device LED will light on for 20 seconds. The next step must be entered while LED is on
          3. Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code number
            • Each digit is separated by 1 second. Ten blinks is equal to the number 0
            • For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks

        Programming a Second TV toAUX Button

          1. Press [AUX] and [ENTER] simultaneously for 3 seconds. The device LED will turn on
            • The device LED will light on for 20 seconds. The next step must be entered while LED is on
          2. Press [TV] to pick up the TV code table
          3. Point the remote control toward the equipment and enter the three-digit code number assigned to your TV brand from the code tables. The equipment will turn off when the correct three-digit code number has been entered.
            TV -- >
          4. Press [VCR] once again. The device LED will blink twice to confirm that the code has been stored

        Programming the System On/Off Button

          The System on/off button can send out up to three power on/off commands for the devices you programmed into the remote control

          1. Press [STB]
          2. Press [System On/Off] and [ENTER] simultaneously for 3 seconds. The [STB] button will turn on for 20 seconds
          3. Press [TV]
          4. Press [VCR] (if adding)
          5. Press [AUX] (if adding)
          6. Press [CH?] to save the power commands you stored. The [STB] button will blink twice to confirm

        Programming Channel Controls

          Channel controls (CH?, CH?, LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:

          STB : STB TV : CBL VCR : VCR AUX : AUX
          If you wish to store the TV channel controls in TV mode, use the following steps

          1. Press the [ENTER] button and [TV] button simultaneously for three seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on
          2. Press the [VOL?] button. The device LED will blink
          3. Press [TV] button. The device LED will blink twice to confirm the programming

            To return TV device to CBL channel repeat steps above replacing [TV] with [STB] in Step 3

        Volume Control

          Volume and Mute control are factory programmed to the respective Device mode you select, as follows:

          STB : TV TV : TV VCR : TV AUX : AUX
          If you wish to store the Cable volume control in CBL mode, use the following steps

          1. Press [STB] button and [ENTER] simultaneously for three seconds
            • The device LED will turn on for 20 seconds. The next step must be performed while the LED is on
          2. Press the [VOL?] button. The device LED will blink
          3. Press [STB] button. The device LED will blink twice to confirm the programming

          To restore the volume control back to your TV in CBL mode, repeat the above steps by replacing [STB] with [TV] in Step 3. To operate the volume control for TV/VCR & TV/DVD combination units, Please use following steps

          1. Press [STB] button and [ENTER] simultaneously for 3 seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on
          2. Press the [VOL?] button
          3. Press the [VCR] button. The device LED will blink twice to confirm the programming

        Low Battery Warning

          When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.

        Memory Lock

          This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.

        Button Functions

          Remote Controls for CA, OR and WA (327)

        HD uDTA


        View printable manual

        • HD uDTA

        Remote Controls for CA, OR and WA (328)

        Expand All | CollapseAll

        Pair Remote to DTA in RF mode

          Pair your remote control with your DTA allowing you to place the device out of sight (in an entertainment center or behind your TV, for example)

          Once your remote is paired to a specific DTA, it will not control any other set-top box in your home

          1. Press [MENU]. Wait for the on-screen menu to come up
          2. Select Settings towards the bottom of the menu
          3. Select Remote Control and then select Remote Control Pairing
          4. Press and hold [Setup] until the LED Indicator turns green
          5. Press [MENU]. Wait for the on-screen menu to come up
          6. Proceed by entering the pairing code displayed in blue on the pairing code pop-up screen
          Note: If you don’t see a pairing code screen, repeat steps 1 and 2

          Removing Remote Control Pairing If you would like your remote to control a different set-top box, you must first un-pair it from the original one.

          1. Press and hold the Setup button until the LED Indicator turns green
          2. Enter 9-8-7 on the remote control
          3. The LED Indicator will blink green twice

        Program by TV Brand Code

          Note: The remote control operates a Sony TV by default. If you have a Sony TV, point the remote control at the TV and press the power button. If the TV operates, there is no need to program the remote control.

          1. Manually turn on the TV
          2. Press and hold [Setup] until the LED Indicator turns green
          3. Enter the 5-digit device code. The LED will flash green twice

            TV -- >

          4. Press [TV Power]. If the TV turns off, the remote is now programmed to operate the TV
          5. Turn the TV back on and make sure that [VOL?/VOL?] and mute buttons work. If not repeat steps 1-4 using the enter the next code listed under the TV brand
            • Please be certain to try all codes listed per your TV’s manufacturer

        Can't Find Your Code?

          Follow the steps below to search for your code:

          1. Manually turn on the TV
          2. Press and hold [Setup] until the LED Indicator turns green
          3. Press [A]
          4. Point the Remote Control to the TV and press [CH?] once every 2 seconds until the TV turns off
          5. Once the TV turns off, Press [Setup]. THE LED will blink green twice if successfully stored

        Volume Control

          To force remote control to send volume control commands to the TV

          1. Press and hold [Setup] until the LED Indicator turns green
          2. Press [VOL?].

          To force remote control to send volume control commands to the DTA

          1. Press and hold [Setup] until the LED Indicator turns green
          2. Press [VOL?]

        Button Functions

          Remote Controls for CA, OR and WA (329)

        Resetting TheRemote

          If you would like to use your remote control for a different set-top box, you must first un-pair the remote control from the current device.

          1. Press and hold [Setup] until the LED Indicator turns green
          2. Enter 9-8-7 on the remote control
          3. The LED Indicator will blink green twice. the same
          4. Try programming the remote again using the steps above

        URC2069 DTA Remote Control


        View printable manual

        • URC2069 DTA Remote Control

        Remote Controls for CA, OR and WA (330)

        Expand All | CollapseAll


        Programming TV into the Remote (Popular Brands)

          Use the following instructions to program the remote for a TV

          1. Turn on the TV
          2. Press and hold SETUP until LED blinks twice
          3. Press the TV POWER key, LED remains ON
          4. Press and hold down the DIGIT key for your TV brand
            Digit TV
            1 Insignia / Dynex
            2 LG / Zenith
            3 Mitsubishi
            4 Panasonic
            5 Philips / Magnavox
            6 Samsung
            7 Sharp
            8 Sony
            9 Toshiba
            0 Vizio
          5. Let go of the key when your TV turns off.. Setup is complete.

        Programming TV into the Remote (Direct Code Entry)

          1. Turn on the TV
          2. Press and hold SETUP until LED blinks twice
          3. Enter the 1st TV code for your brand from the code list to the right. LED blinks twice

            TV -- >

          4. Press the TV POWER key to test TV control. If the TV turns off, setup is complete
          5. If TV does not turn off, repeat steps 1-4 using the next code for your TV brand

        Code Search

          if the Brand of your TV is not listed in the code list, try searching for your code

          1. Turn on the TV
          2. Press and hold SETUP until LED blinks twice
          3. Press and hold down the OK/SELECT key
          4. Let go of the OK/SELECT key when the TV turns offf

        Volume Control

          This remote can be configured to control the volume through any programmed device. When programming the remote for a TV or DTA, the last programmed device will be the volume source. This setting can be changed at any time with the following sequence(s): Volume Control Through TV

          1. Press and hold SETUP until LED blinks twice
          2. Press VOL +. The LED will blink twice as confirmation

          Volume Control Through DTA

          1. Press and hold SETUP until LED blinks twice
          2. Press MUTE. The LED will blink 4 times

        Button Descriptions

          Remote Controls for CA, OR and WA (331)

        URC2068BC2 DTA Remote


        View printable manual

        • URC2068BC2 DTA Remote

        Remote Controls for CA, OR and WA (332)

        Expand All | CollapseAll


        Programming TV into the Remote (Popular Brands)

          Use the following instructions to program the remote for a TV

          1. Turn on the TV
          2. Press and hold SETUP until LED blinks twice
          3. Press the TV POWER key, LED remains ON
          4. Press and hold down the DIGIT key for your TV brand
            Digit TV
            1 Insignia / Dynex
            2 LG / Zenith
            3 Mitsubishi
            4 Panasonic
            5 Philips / Magnavox
            6 Samsung
            7 Sharp
            8 Sony
            9 Toshiba
            0 Vizio
          5. Let go of the key when your TV turns off.. Setup is complete.

        Programming TV into the Remote (Direct Code Entry)

          1. Turn on the TV
          2. Press and hold SETUP until LED blinks twice
          3. Enter the 1st TV code for your brand from the code list to the right. LED blinks twice

            TV -- >

          4. Press the TV POWER key to test TV control. If the TV turns off, setup is complete
          5. If TV does not turn off, repeat steps 1-4 using the next code for your TV brand

        Code Search

          if the Brand of your TV is not listed in the code list, try searching for your code

          1. Turn on the TV
          2. Press and hold SETUP until LED blinks twice
          3. Press and hold down the OK/SELECT key
          4. Let go of the OK/SELECT key when the TV turns offf

        Volume Control

          This remote can be configured to control the volume through any programmed device. When programming the remote for a TV or DTA, the last programmed device will be the volume source. This setting can be changed at any time with the following sequence(s): Volume Control Through TV

          1. Press and hold SETUP until LED blinks twice
          2. Press VOL +. The LED will blink twice as confirmation

          Volume Control Through DTA

          1. Press and hold SETUP until LED blinks twice
          2. Press MUTE. The LED will blink 4 times

        Button Descriptions

          Remote Controls for CA, OR and WA (333)

        UR3-SR3


        View printable manual

        • UR3-SR3

        Remote Controls for CA, OR and WA (334)

        Expand All | CollapseAll


        Manual Programming

          The remote control can be programmed by entering a three-digit code number that corresponds to particular brands and models of equipment

          1. Turn on the equipment that you want the remote control to operate (Cable Box, TV, VCR, or DVD)
          2. Press the [Device] button and the [SELECT] button simultaneously for three seconds. The corresponding device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 20 seconds. The next step must be entered while the LED is on
          3. Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. If there are more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off
            Cable Converter- [CBL] key ?
            TV - [TV] key ?
            VCR - [VCR] key ?
            TV/VCR combo* - [VCR] key ?
            DVD - [VCR] key ?
            TV/DVD combo* - [VCR] key ?
            • You can verify that you have selected the correct code by pressing the [MUTE] button. The equipment should turn back on. Then try all of the functions on the remote control (i.e. VOL?, VOL?, CH?, CH?, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, repeat the instructions from STEP 3 using the next three digit code number from the brand list
          4. Store the three-digit code by pressing the same [Device] button once again. The device LED will blink twice to confirm that the code has been stored.

          *To operate the volume control on TV/VCR & TV/DVD combination units, see Volume Control below

        Auto Search Method

          If none of the three digit code numbers assigned to your brand of equipment works, or the code table does not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by following steps:

          1. Turn on the equipment that you want the remote control to operate (Cable Box, TV or DVD)
          2. Press the [Device] button and [SELECT] simultaneously for three seconds

            The device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 30 seconds. The next step must be entered while the LED is on

          3. Press [CH?] or [CH?] one at a time or keep it pressed. The remote will emit a series of Power ON/OFF code signals. Release [CH?] or [CH?] as soon as the equipment turns off

            You can verify that you have selected the correct code by pressing [MUTE]. The equipment should turn back on. Then try all of the functions on the remote control (i.e. volume, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, repeat the instructions from STEP 3 to continue the Auto Search Method

          4. Press the same [Device] button to store the code. The device LED will blink twice to confirm that the code has been stored.

        Code Number Readback

          This is useful for determining a device code that was set using the Auto Search Method above

          1. Press the [Device] button and [SELECT] simultaneously for 3 seconds
          2. The device LED will light on for 20 seconds. The next step must be entered while LED is on
          3. Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code number
            • Each digit is separated by 1 second. Ten blinks is equal to the number 0
            • For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks

        Programming aSecond TV to VCR key

          1. Press [VCR] and [SELECT] simultaneously for 3 seconds.
            • The device LED will light on for 30 seconds. The next step must be entered while LED is on
          2. Press [TV]
          3. Point the remote control toward the equipment and enter the three-digit code number assigned to your TV brand from the code tables. The equipment will turn off when the correct three-digit code number has been entered.

            TV ?

          4. Press [VCR] once again. The device LED will blink twice to confirm that the code has been stored

        Volume Control

          Volume and Mute control are factory programmed to the respective Device mode you select, as follows:

          CBL : TV TV : TV DVD : TV

          If you wish to store the Cable volume control in CBL mode, use the following steps

          1. Press the [SELECT] button and [CBL] button simultaneously for three seconds.

            The device LED will turn on for 20 seconds. The next step must be performed while the LED is on

          2. Press the [VOL?] button. The device LED will blink
          3. Press [CBL] button. The device LED will blink twice to confirm the programming

          To restore the volume control back to your TV in CBL mode, repeat the above steps by replacing [CBL] with [TV] in Step 3.

          To operate the volume control for TV/VCR & TV/DVD combination units, Please use following steps

          1. Press the [CBL] button and the [SELECT] button simultaneously for 3 seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on
          2. Press the [VOL?] button
          3. Press the [VCR] button. The CBL device LED will blink twice to confirm the programming

        Programming Channel Control

          Channel controls are factory-programmed to automatically transfer to the respective Device mode you select, as follows:

          CBL : CBL TV : CBL DVD : DVD

          If you wish to store the TV channel controls in TV mode, use the following steps.

          1. Press the [SELECT] button and [TV] button simultaneously for three seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on

          2. Press the [VOL?] button. The device LED will blink

          3. Press [TV] button. The device LED will blink twice to confirm the programming

          To return TV device to CBL channel repeat steps above replacing [TV] with [CBL] in Step 3

        Low Battery Warning

          When the battery is low, the remote control LED blinks 2 times whenever a [Device] button is pressed to turn on equipment.

        Memory Lock

          This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.

        Button Descriptions

          Remote Controls for CA, OR and WA (335)

        UR3-SR2


        View printable manual

        • UR3-SR2

        Remote Controls for CA, OR and WA (336)

        Expand All | CollapseAll


        Manual Programming

          The remote control can be programmed by entering a three-digit code number that corresponds to particular brands and models of equipment

          1. Turn on the equipment that you want the remote control to operate (Cable Box, TV, VCR, or DVD)
          2. Press the [Device] button and the [SELECT] button simultaneously for three seconds. The corresponding device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 20 seconds. The next step must be entered while the LED is on
          3. Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. If there are more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off
            Cable Converter- [CBL] key ?
            TV - [TV] key ?
            VCR - [VCR] key ?
            TV/VCR combo* - [VCR] key ?
            DVD - [VCR] key ?
            TV/DVD combo* - [VCR] key ?
            • You can verify that you have selected the correct code by pressing the [MUTE] button. The equipment should turn back on. Then try all of the functions on the remote control (i.e. VOL?, VOL?, CH?, CH?, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, repeat the instructions from STEP 3 using the next three digit code number from the brand list
          4. Store the three-digit code by pressing the same [Device] button once again. The device LED will blink twice to confirm that the code has been stored.

          *To operate the volume control on TV/VCR & TV/DVD combination units, see Volume Control below

        Auto Search Method

          If none of the three digit code numbers assigned to your brand of equipment works, or the code table does not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by following steps:

          1. Turn on the equipment that you want the remote control to operate (Cable Box, TV or DVD)
          2. Press the [Device] button and [SELECT] simultaneously for three seconds

            The device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 30 seconds. The next step must be entered while the LED is on

          3. Press [CH?] or [CH?] one at a time or keep it pressed. The remote will emit a series of Power ON/OFF code signals. Release [CH?] or [CH?] as soon as the equipment turns off

            You can verify that you have selected the correct code by pressing [MUTE]. The equipment should turn back on. Then try all of the functions on the remote control (i.e. volume, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, repeat the instructions from STEP 3 to continue the Auto Search Method

          4. Press the same [Device] button to store the code. The device LED will blink twice to confirm that the code has been stored.

        Code Number Readback

          This is useful for determining a device code that was set using the Auto Search Method above

          1. Press the [Device] button and [SELECT] simultaneously for 3 seconds
          2. The device LED will light on for 20 seconds. The next step must be entered while LED is on
          3. Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code number
            • Each digit is separated by 1 second. Ten blinks is equal to the number 0
            • For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks

        Programming aSecond TV to VCR key

          1. Press [VCR] and [SELECT] simultaneously for 3 seconds.
            • The device LED will light on for 30 seconds. The next step must be entered while LED is on
          2. Press [TV]
          3. Point the remote control toward the equipment and enter the three-digit code number assigned to your TV brand from the code tables. The equipment will turn off when the correct three-digit code number has been entered.

            TV ?

          4. Press [VCR] once again. The device LED will blink twice to confirm that the code has been stored

        Volume Control

          Volume and Mute control are factory programmed to the respective Device mode you select, as follows:

          CBL : TV TV : TV DVD : TV

          If you wish to store the Cable volume control in CBL mode, use the following steps

          1. Press the [SELECT] button and [CBL] button simultaneously for three seconds.

            The device LED will turn on for 20 seconds. The next step must be performed while the LED is on

          2. Press the [VOL?] button. The device LED will blink
          3. Press [CBL] button. The device LED will blink twice to confirm the programming

          To restore the volume control back to your TV in CBL mode, repeat the above steps by replacing [CBL] with [TV] in Step 3.

          To operate the volume control for TV/VCR & TV/DVD combination units, Please use following steps

          1. Press the [CBL] button and the [SELECT] button simultaneously for 3 seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on
          2. Press the [VOL?] button
          3. Press the [VCR] button. The CBL device LED will blink twice to confirm the programming

        Programming Channel Control

          Channel controls are factory-programmed to automatically transfer to the respective Device mode you select, as follows:

          CBL : CBL TV : CBL DVD : DVD

          If you wish to store the TV channel controls in TV mode, use the following steps.

          1. Press the [SELECT] button and [TV] button simultaneously for three seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on

          2. Press the [VOL?] button. The device LED will blink

          3. Press [TV] button. The device LED will blink twice to confirm the programming

          To return TV device to CBL channel repeat steps above replacing [TV] with [CBL] in Step 3

        Low Battery Warning

          When the battery is low, the remote control LED blinks 2 times whenever a [Device] button is pressed to turn on equipment.

        Memory Lock

          This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.

        Button Descriptions

          Remote Controls for CA, OR and WA (337)

        UJ4-EXP


        View printable manual

        • UJ4-EXP

        Remote Controls for CA, OR and WA (338)

        Expand All | CollapseAll

        Three-Digit Code Programming Method

          1. Turn on the equipment you wish to program. (TV, VCR, or AUX)
          2. Press and hold the appropriate device key (TV, VCR, AUX*) for three seconds until all device keys begin to flash. Release the key. The selected device key will continue to flash
          3. Enter the three digit code using the number keys. After you press the first digit, the device key should light and stay on. After you press the last digit, the device key should flash three times and turn off.

            TV -- >

            VCR -- >

            TV/VCR (using VCR key) -- >

            Audio Device (using AUX* key) -- >

            DVD (using VCR key) -- >

            TV/DVD (using VCR key)** -- >

            PVR (using VCR key) -- >

            *If you are programming the AUXkey, an additional step if needed:

            1. Press and hold the AUX key until all four device keys begin to flash. Release the AUX key. The AUX key will continue to flash
            2. Press the desired device key
              • TV - for an additional TV
              • VCR - for an additional VCR, DVD player, TV/DVD combo, TV/VCR combo, or PVR
              • AUX For audio receiver/ amplifier codes
            3. Use the three digit code above as noted

            ** Emerson, Sharp, and Sylvania TV/DVD combos require that the TV and DVD sections of the unit be programmed separately

          4. Point the remote at the device and press POWER. If the device turns on or off, you have finished programming the device
          5. Press [TV] ( or [VCR]) again. The device LED will blink twice to confirm that the code has been stored

          Please Note:

          • Try all the functions on the remote control. If any of the functions do not work as they should, repeat from Step 2 using the next three-digit code number from the same brand list.

        SMART SCANTM AUTOMATIC PROGRAMMING

          The Smart Scan automatic programming method will allow you to cycle through all the available codes in the remote until you find the right code for a device.

          1. Manually turn on power to the device you want to program the remote for
          2. For TV and VCR modes, press and hold the appropriate device key for three seconds until all device keys begin to flash
          3. Release the key then press and release [POWER]. The device key will stop flashing and stay on. Proceed to Step 4 to perform Smart Scan

            For AUX mode, press and hold the [ AUX] key for three seconds until the [AUX] key begins to flash. Release the key. Then press the TV, VCR, or AUX device key, depending on which device you want to assign to the [ AUX] key. The [ AUX] key will stop flashing and stay on. Press and release the POWER key. Proceed to Step 3 to perform the Smart Scan

          4. Point the remote control at the device. Repeatedly press and release (or press and hold) the ? key until the device turns off. If holding the ARROW UP or ARROW DOWN key, the remote will send a code approximately once every second. If pressing keys repeatedly, one code is sent each time the key is pressed. If you accidentally press the ? key after the device has turned off, press the ? key to return to the previous device code
          5. While performing Smart Scan, you can pause to test other device functions using the remote control. If primary functions do not work, resume Smart Scan by pressing the ?? keys to find another code that turns off the device. Then test the functions again
          6. When you are satisfied that all primary functions are working, press [SELECT] to lock in the code. The device key will then flash three times
            • NOTE: When scanning for DVD players, PVRs, TV/VCR combos, and TV/DVD player combos, use the Smart Scan procedure with the VCR device key

        Code NumberReadback

          Perform the following steps to read the code currently set for a device. This is useful for retrieving a device code that was set using the Smart Scan procedure above

          1. Press and hold a device key until the four device keys flash twice. Release the key. The selected device key will continue to flash
          2. Press and release [ SELECT]. The device key flashes each of the three digits in the code. A pause separates each digit. For example, three flashes represent the number 3, and a rapid flicker represents 0. A code of 103 will be shown as:

            FLASH <pause> FLICKER <pause> FLASH, FLASH, FLASH

          3. Count and record the sequence of flashes to determine the three-digit code

        Master PowerControl

          The Master Power function allows you to turn off and on two or more devices simultaneously with a single press of the power button. Follow these steps to program the Master Power function

          1. Press and hold the CBL device key until all the device keys begin to flash. Release the CBL key. The CBL key will continue to flash
          2. Press and release the POWER key
          3. One at a time, and in the order you want, press and release the device key(s) you wish to be controlled by Master Power ([CBL], [TV], [VCR], [AUX])
            • NOTE: If no keys are pressed in this step, no change will occur in Master Power programming
          4. Press and release [ POWER]. The device keys should flash and turn off
          5. Manually turn on all devices. Then test the Master Power control by pressing [ POWER]

          To disable Master Power, select only one device for Master Power (any device can be selected). The remote will now control the power ON/OFF of each device separately

          • NOTE: Once Master Power has been programmed for two or more devices, pressing [ POWER] in normal operation will cause the remote to transmit the POWER on/off commands for those devices selected during Master Power programming, UNLESS you do the following: To transmit a POWER on/off command for a device NOT included in the Master Power selection, press the DEVICE key for that device immediately (within five seconds) before pressing the POWER key.

        Volume Control

          By default, your remote controls volume individually through each device selected. AUX is initially an audio device operating its own volume and mute. To set volume through a different device, follow these steps:

          1. Press and hold [CBL] until all the device keys begin to flash. Release the [CBL] key. [CBL] will continue to flash
          2. Press and release [VOL?] then [VOL?]. The device key will stop flashing and remain on. Press and release the [TV], [CBL], [VCR], or [AUX] key corresponding to the device you wish to control volume. After you release the key, [CBL] will flash three times and turn off

            NOTE:

            • Only select the [VCR] key if you have a TV/VCR combo or TV/DVD combo programmed under the VCR device mode
            • If a device is selected that does not have volume control, the programming cancels and does not flash a confirmation sequence

          To return volume control to the default state (where the volume keys can control volume for each device):

          1. Press [CBL] until all the device keys begin to flash. Release [CBL]. [CBL] will continue to flash
          2. Press and release [VOL?]. [CBL] will stop flashing and stay on. Press and release [VOL?], and then [ SELECT]. After you release [ SELECT], [CBL] will flash three times and turn off.

        Channel Lock

          Channel controls are factory-programmed to automatically transfer to the respective Device mode you select, as follows:

          CBL : CBL TV : CBL DVD : DVD AUX: AUX

          To deactivate Channel Lock, follow these steps

          1. Press and hold [CBL] until all the device keys begin to flash. Release [CBL]. [CBL] will continue to flash
          2. Press and release [CH?], then [CH?], and finally [ SELECT]. [CBL] will flash three times to confirm the procedure

          To reactivate Channel Lock, repeat these steps

        Button Functions

          Remote Controls for CA, OR and WA (339)

        UF4-200C


        View printable manual

        • UF4-200C

        Remote Controls for CA, OR and WA (340)

        Expand All | CollapseAll


        Setting up Your Remote

          1. On the remote control, press and hold the appropriate mode key until the four mode keys flash twice. The mode key will continue to flash
          2. Enter the three-digit code

            • After you press the first digit, the mode key should light and stay on. After you press the last digit, the mode key should flash three times and turn off
            • If the mode key does not flash three times before turning off, the code is invalid for this device type. Repeat the procedure with another device code
          3. Point the remote at the device and press POWER. If the device turns on or off, you have finished programming
          4. If you have tried all the codes listed for the manufacturer and the device does not respond, refer to the CodeScan™ section later in this manual

        Setting up your Remote for an Auxilliary Device

          1. Press and hold AUX until the four mode keys flash twice. The AUX key will continue to flash
          2. Press and release the appropriate mode key for the device (VCR for a video cassette recorder, TV for a television, and CABLE for a cable device) until the four mode keys flash twice

            Look up the device manufacturer in the Television Codes, VCR codes sections, or Converter Codes sections and enter the three-digit code for your TV, VCR or Cable device

          3. After you press the first digit, the AUX key should light and stay on. After you press the last digit, the AUX key should flash three times and turn off
          4. If the AUX key does not flash three times before turning off, the code is invalid for this device type. Repeat the procedure with another device code
          5. Point the remote at the device and press POWER. If the device turns on or off, you have finished programming. If you have tried all the codes listed for the manufacturer and the device does not respond, refer to the CodeScan™ section later in this manual.

        Codescan

          If none of the codes listed for your Cable Box, TV, or VCR works, the CodeScan™ method will allow you to cycle through all the available codes in the remote until you find the right Cable Box, TV, or VCR code.

          1. Manually turn on power to the device for which you want to program the remote (TV, CABLE, AUX, VCR)
          2. Press and hold a mode key for approximately three seconds until the four mode keys flash twice. The selected mode key will continue to flash
          3. Press POWER. The mode key will stop flashing and remain on
          4. Point the remote control at the device
          5. Press and release the? key repeatedly and slowly. Each time you press the key, the remote sends the power-off command using a different device code
          6. When the device turns off, that means that the remote has been programmed with a code that can control the device. If you accidentally press the ? key after the device has turned off, press the ? key to return to the previous device code
          7. Test whether other functions operate using the remote control. If a primary function does not work, continue to press the ? key to find another code that turns off the device. Then test the functions again
          8. When you are satisfied that all primary functions are working, press OK to lock in the code

        Recalling a Device Code

          Perform the following steps to read the code currently set for a device. This is useful for retrieving a device code that was set using the CodeScan™ method.

          1. Press and hold a mode key until the four mode keys flash twice. The selected mode key will continue to flash
          2. Press HELP. The mode key flashes each of the three digits in the code
            • A pause separates each digit
            • For example, three flashes represent the number 3
            • Rapid flashing represents 0
          3. Count and record the sequence of flashes to determine the three-digit code

        Programming Volume Control

          By default, volume is controlled through your cable box; but if you have a TV that permits volume control, and you would to control volume through it, follow these steps (this procedure does not affect the device codes you set previously)

          1. Press and hold CABLE for approximately three seconds until the four mode keys flash twice. The CABLE key will continue to flash
          2. Press TV. The CABLE key will flash three times and turn off
          3. You now control the volume through the TV whenever you change the volume level in Cable mode

          If you would like to return to volume control through the cable box, follow these steps:

          1. Press and hold CABLE for approximately three seconds until the four mode keys flash twice. The CABLE key will continue to flash
          2. Press CABLE. The CABLE key will flash three times and turn off
          3. You now control the volume through the TV whenever you change the volume level in Cable mode

        Button Functions

          Remote Controls for CA, OR and WA (341)

        Installing/Replacing Batteries

          Before you can program or operate the remote control, you must install two Alkaline AA batteries

          1. Remove the battery compartment cover on the back of your remote control
          2. Check battery polarity carefully, and install the batteries as shown in the illustration belowt
          3. Replace the battery compartment cover

          IMPORTANT NOTE: Weak batteries may disrupt normal operation of the remote


          Remote Controls for CA, OR and WA (342)

        REMOTE FINDER

        • REMOTE FINDER

        Match the first button on the left of the top row to identify the remote control
        Remote Controls for CA, OR and WA (343)

        Expand All | CollapseAll


        Remote Controls for CA, OR and WA (344)

        AUD Button

        AUX Button

        DTA Button

        MODE

        MOT Button

        Power Button

        Setup Button

        System On/Off Button

        TV Button

        TV Pwr Button

        VCR Button

        Video Input Button

        Internal Information

        Commercial Agent Steps

        Financial Agent Steps

        Management Steps

        Remote Controls for CA, OR and WA (2024)
        Top Articles
        Latest Posts
        Recommended Articles
        Article information

        Author: Rubie Ullrich

        Last Updated:

        Views: 5434

        Rating: 4.1 / 5 (72 voted)

        Reviews: 95% of readers found this page helpful

        Author information

        Name: Rubie Ullrich

        Birthday: 1998-02-02

        Address: 743 Stoltenberg Center, Genovevaville, NJ 59925-3119

        Phone: +2202978377583

        Job: Administration Engineer

        Hobby: Surfing, Sailing, Listening to music, Web surfing, Kitesurfing, Geocaching, Backpacking

        Introduction: My name is Rubie Ullrich, I am a enthusiastic, perfect, tender, vivacious, talented, famous, delightful person who loves writing and wants to share my knowledge and understanding with you.